cve
Veille des vulnérabilités Archive complète
identifiantvulnérabilitésévéritépublié
CVE-2026-63924In the Linux kernel, the following vulnerability has been resolved:
ipv6: exthdrs: refresh nh pointer after ipv6_hop_jumbo()
ipv6_hop_jumbo() calls pskb_trim_rcsum(), which can change skb pointers.
Let's recompute nh pointer to make sure any change won't mess things up.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-63925In the Linux kernel, the following vulnerability has been resolved:
macsec: fix replay protection at XPN lower-PN wrap
In macsec_post_decrypt(), when pn is U32_MAX, pn + 1 overflows u32 to 0
and the first branch never fires. If next_pn_halves.lower is also in the
upper half, pn_same_half(pn, lower) is true and the XPN else-if does not
fire either, leaving next_pn_halves unchanged. An attacker that captures
the legitimate frame carrying pn == 0xFFFFFFFF on an XPN association
can then replay it indefinitely, since lowest_pn never rises above
the captured pn and macsec_decrypt() reconstructs the same IV.
Extend the XPN else-if to also fire when pn + 1 wraps to 0, so receipt
of pn == U32_MAX advances next_pn_halves to (upper + 1, 0).Analyse NVD en cours Élevée CVSS 8.1 CVE-2026-63926In the Linux kernel, the following vulnerability has been resolved:
bpf: sockmap: fix tail fragment offset in bpf_msg_push_data
When bpf_msg_push_data() inserts data in the middle of a scatterlist
entry, it splits the original entry into a left fragment and a right
fragment.
The right fragment offset is page-local, but the code advances it with
`start`, which is the message-global insertion point. For inserts into a
non-first SG entry, this over-advances the offset and leaves the split
layout inconsistent.
Advance the right fragment offset by the fragment-local delta,
`start - offset`, which matches the length removed from the front of the
original entry.Analyse NVD en cours Élevée CVSS 8.4 CVE-2026-63927In the Linux kernel, the following vulnerability has been resolved:
usb: dwc2: Fix use after free in debug code
We're not allowed to dereference "urb" after calling
usb_hcd_giveback_urb() so save the urb->status ahead of time.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-63930In the Linux kernel, the following vulnerability has been resolved:
iio: buffer: hw-consumer: fix use-after-free in error path
In the err_put_buffers cleanup path of iio_hw_consumer_alloc(), the code
was using list_for_each_entry() to iterate through buffers while calling
iio_buffer_put() which can free the current buffer if refcount drops to 0.
The list_for_each_entry() loop macro then evaluates buf->head.next to
continue iteration, accessing the freed buffer.
Fix this by using list_for_each_entry_safe().Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-63937In the Linux kernel, the following vulnerability has been resolved:
KVM: SEV: Use READ_ONCE() when reading entries/indices from PSC buffer
Use READ_ONCE() when reading entries/indices from the guest-accessible
Page State Change buffer to defend against TOCTOU bugs.
Don't bother with READ_ONCE()/WRITE_ONCE() for cases where KVM is writing
(and not consuming the result!), as the guest isn't supposed to touch the
buffer while it's being processed. I.e. using READ_ONCE() is all about
protecting against misbehaving guests.Analyse NVD en cours Élevée CVSS 8.8 CVE-2026-63938In the Linux kernel, the following vulnerability has been resolved:
KVM: SEV: Check PSC request indices against the actual size of the buffer
When processing Page State Change (PSC) requests, validate the PSC buffer
against the effective size of the scratch area, which could be less than
the maximum size if the guest provided a pointer that isn't exactly at the
start of the GHCB shared buffer.Analyse NVD en cours Critique CVSS 9.3 CVE-2026-63939In the Linux kernel, the following vulnerability has been resolved:
KVM: SEV: Compute the correct max length of the in-GHCB scratch area
When setting the length of the GHCB scratch area, and the area is in the
GHCB shared buffer, set the effective length of the scratch area to the max
possible size given the start of the guest-provided pointer, and the end of
the shared buffer.
The code was "fine" when first introduced, as KVM doesn't consult the
length of the buffer when emulating MMIO, because the passed in @len always
specifies the *max* size required. But for PSC requests, the incoming @len
is just the minimum length (to process the header), and KVM needs to know
the full size of the scratch area to avoid buffer overflows (spoiler alert).
Opportunistically rename @len => @min_len to better reflect its role.Analyse NVD en cours Critique CVSS 9.3 CVE-2026-63940In the Linux kernel, the following vulnerability has been resolved:
KVM: SEV: Ignore Port I/O requests of length '0'
Explicitly ignore Port I/O requests of length '0' (or count '0'), so that
setting up the software scratch area (and other code) doesn't have to
worry about underflowing the length, and to allow for WARNing on trying
to configure the scratch area with len==0.Analyse NVD en cours Critique CVSS 9.3 CVE-2026-63941In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Correctly cap ZCR_EL2 provided by a guest hypervisor
ZCR_EL2 can be updated by a VHE guest hypervisor either using ZCR_EL2
(which traps) or ZCR_EL1 (which does not trap). KVM handles both in
different way:
- on ZCR_EL2 trap, ZCR_EL2.LEN is immediately capped at the VM's own
VL limit. This has the potential to break existing SW that relies
on the full LEN field to be stateful.
- on ZCR_EL1 access, we do absolutely nothing.
On restoring the SVE context for an L2 guest, we directly restore the
guest hypervisor's view of ZCR_EL2 into the physical ZCR_EL2. If the
guest's view of the register was updated using the ZCR_EL2 accessor,
the value has already been sanitised (with the caveat mentioned above).
But if the guest used ZCR_EL1, the raw value is written into the HW,
and the L2 guest can now access VLs that it shouldn't.
Fix all the above by moving the VL capping to the restore points,
ensuring that:
- the HW is always programmed with a capped value, irrespective of
the accessor being used,
- the ZCR_EL2.LEN field is always completely stateful, irrespective
of the accessor being used.
Additionally, move ZCR_EL2 to be a sanitised register, ensuring that
only the LEN field is actually stateful. This requires some creative
construction of the RES0 mask, as the sysreg generation script does
not yet generate RAZ/WI fields.
[maz: rewrote commit message, tidy up access_zcr_el2()]Analyse NVD en cours Élevée CVSS 8.8 CVE-2026-63942In the Linux kernel, the following vulnerability has been resolved:
parport: Fix race between port and client registration
The parport subsystem registers port devices before they are fully
initialised, resulting in a race condition where client drivers such
as lp can attach to ports that are not completely initialised or even
being torn down.
When the port and client drivers are built as modules and loaded
around the same time during boot, this occasionally results in a
crash. I was able to make this happen reliably in a VM with a
PC-style parallel port by patching parport_pc to fail probing:
> --- a/drivers/parport/parport_pc.c
> +++ b/drivers/parport/parport_pc.c
> @@ -2069,7 +2069,7 @@ static struct parport *__parport_pc_probe_port(unsigned long int base,
> if (!p)
> goto out3;
>
> - base_res = request_region(base, 3, p->name);
> + base_res = NULL;
> if (!base_res)
> goto out4;
>
and then running:
while true; do
modprobe lp & modprobe parport_pc
wait
rmmod lp parport_pc
done
for a few seconds.
In the long term I think port registration should be changed to put
the call to device_add() inside parport_announce_port(), but since the
latter currently cannot fail this will require changing all port
drivers.
For now, add a flag to indicate whether a port has been "announced"
and only try to attach client drivers to ports when the flag is set.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-63944In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: fix UAF in hci_le_create_cis_sync
hci_le_create_cis_sync() dereferences conn->conn_timeout after releasing
both rcu_read_lock() and hci_dev_lock(hdev). The conn pointer was
obtained from an RCU-protected iteration over hdev->conn_hash.list and
is not valid once these locks are dropped. A concurrent disconnect can
free the hci_conn between the unlock and the dereference, causing a
use-after-free read.
The cancellation mechanism in hci_conn_del() cannot prevent this because
hci_le_create_cis_pending() queues hci_create_cis_sync with data=NULL:
hci_cmd_sync_queue(hdev, hci_create_cis_sync, NULL, NULL);
While hci_conn_del() dequeues with data=conn:
hci_cmd_sync_dequeue(hdev, NULL, conn, NULL);
Since NULL != conn, the lookup in _hci_cmd_sync_lookup_entry() never
matches, and the pending work item is not cancelled.
Fix this by saving conn->conn_timeout into a local variable while the
locks are still held, so the stale conn pointer is never dereferenced
after unlock.
This is the same class of bug as the one fixed by commit 035c25007c9e
("Bluetooth: hci_sync: Fix UAF on le_read_features_complete") which
addressed the identical pattern in a different function.
This vulnerability was identified using 0sec.ai, an open-source
automated security auditing platform (https://github.com/0sec-labs).Analyse NVD en cours Élevée CVSS 8.8 CVE-2026-63945In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: serialize iso_sock_clear_timer with socket lock
iso_sock_close() calls iso_sock_clear_timer() before acquiring
lock_sock(sk).
iso_sock_clear_timer() reads iso_pi(sk)->conn twice without the
socket lock held:
if (!iso_pi(sk)->conn)
return;
cancel_delayed_work(&iso_pi(sk)->conn->timeout_work);
Concurrently, iso_conn_del() executes under lock_sock(sk) and calls
iso_chan_del(), which sets iso_pi(sk)->conn to NULL and may result in
the final reference to the connection being dropped:
CPU0 CPU1
---- ----
iso_sock_clear_timer()
if (conn != NULL) ... lock_sock(sk)
iso_chan_del()
iso_pi(sk)->conn = NULL
cancel_delayed_work(conn) /* NULL deref or UAF */
iso_pi(sk)->conn is not stable across the unlock window, causing a
NULL pointer dereference or use-after-free.
Serialize iso_sock_clear_timer() with the socket lock by moving it
inside lock_sock()/release_sock(), matching the pattern used in
iso_conn_del() and all other call sites.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-63946In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: fix UAF in iso_recv_frame
iso_recv_frame reads conn->sk under iso_conn_lock but releases the lock
before using sk, with no reference held. A concurrent iso_sock_kill()
can free sk in that window, causing use-after-free on sk->sk_state and
sock_queue_rcv_skb().
Fix by replacing the bare pointer read with iso_sock_hold(conn), which
calls sock_hold() while the spinlock is held, atomically elevating the
refcount before the lock drops. Add a drop_put label so sock_put() is
called on all exit paths where the hold succeeded.Analyse NVD en cours Élevée CVSS 8.8 CVE-2026-63947In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: HIDP: fix missing length checks in hidp_input_report()
hidp_input_report() reads keyboard and mouse payload data from an skb
without first verifying that skb->len contains enough data.
hidp_recv_intr_frame() pulls the 1-byte HIDP header before dispatching
to hidp_input_report(). If a paired device sends a truncated packet,
the handler reads beyond the valid skb data, resulting in an
out-of-bounds read of skb data. The OOB bytes may be interpreted as
phantom key presses or spurious mouse movement.
Replace the open-coded length tracking and pointer arithmetic with
skb_pull_data() calls. skb_pull_data() returns NULL if the requested
bytes are not present, eliminating the need for a manual size variable
and the separate skb->len guard.Analyse NVD en cours Élevée CVSS 8.8 CVE-2026-63950In the Linux kernel, the following vulnerability has been resolved:
mm/rmap: initialize nr_pages to 1 at loop start in try_to_unmap_one
Initialize nr_pages to 1 at the start of each loop iteration, like
folio_referenced_one() does.
Without this, nr_pages computed by a previous folio_unmap_pte_batch() call
can be reused on a later iteration that does not run
folio_unmap_pte_batch() again.
mmap a 64K large folio with MAP_ANONYMOUS | MAP_DROPPABLE, then call
madvise(MADV_FREE), then make the last page device-exclusive via
HMM_DMIRROR_EXCLUSIVE.
Trigger node reclaim through sysfs. Now, in try_to_unmap_one(), we will
first clear the first 15 out of 16 entries mapping the lazyfree folio.
This will set nr_pages to 15. In the next pvmw walk, this nr_pages gets
reused on a device-exclusive pte, thus potentially corrupting folio
refcount/mapcount.
At the moment, I have a userspace program which can make the kernel spit
out a trace, but the blow up is in folio_referenced_one(), because there
are existing bugs in the interaction between device-private and rmap
(which too I am investigating). I did a one liner kernel change to avoid
going into folio_referenced_one(), and the kernel blows up at
folio_remove_rmap_ptes in try_to_unmap_one which is what I wanted.
Note that the bug is there not since file folio batching but lazyfree
folio batching, since device-exclusive only works for anonymous folios.
Userspace visible effect is simply kernel crashing somewhere due to
refcount/mapcount corruption.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-63951In the Linux kernel, the following vulnerability has been resolved:
zram: fix use-after-free in zram_writeback_endio
A crash was observed in zram_writeback_endio due to a NULL pointer
dereference in wake_up. The root cause is a race condition between the
bio completion handler (zram_writeback_endio) and the writeback task.
In zram_writeback_endio, wake_up() is called on &wb_ctl->done_wait after
releasing wb_ctl->done_lock. This creates a race window where the
writeback task can see num_inflight become 0, return, and free wb_ctl
before zram_writeback_endio calls wake_up().
CPU 0 (zram_writeback_endio) CPU 1 (writeback_store)
============================ ============================
zram_writeback_slots
zram_submit_wb_request
zram_submit_wb_request
wait_event(wb_ctl->done_wait)
spin_lock(&wb_ctl->done_lock);
list_add(&req->entry, &wb_ctl->done_reqs);
spin_unlock(&wb_ctl->done_lock);
wake_up(&wb_ctl->done_wait);
zram_complete_done_reqs
spin_lock(&wb_ctl->done_lock);
list_add(&req->entry, &wb_ctl->done_reqs);
spin_unlock(&wb_ctl->done_lock);
while (num_inflight) > 0)
spin_lock(&wb_ctl->done_lock);
list_del(&req->entry);
spin_unlock(&wb_ctl->done_lock);
// num_inflight becomes 0
atomic_dec(num_inflight);
// Leave zram_writeback_slots
// Free wb_ctl
release_wb_ctl(wb_ctl);
// UAF crash!
wake_up(&wb_ctl->done_wait);
This patch fixes this race by using RCU. By protecting wb_ctl with
rcu_read_lock() in zram_writeback_endio and using kfree_rcu() to free it,
we ensure that wb_ctl remains valid during the execution of
zram_writeback_endio.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-63952In the Linux kernel, the following vulnerability has been resolved:
memfd: deny writeable mappings when implying SEAL_WRITE
When SEAL_EXEC is added, SEAL_WRITE is implied to make W^X. But the
implied seal is set after the check that makes sure the memfd can not have
any writable mappings. This means one can use SEAL_EXEC to apply
SEAL_WRITE while having writeable mappings.
This breaks the contract that SEAL_WRITE provides and can be used by an
attacker to pass a memfd that appears to be write sealed but can still be
modified arbitrarily.
Fix this by adding the implied seals before the call for
mapping_deny_writable() is done.Analyse NVD en cours Élevée CVSS 8.4 CVE-2026-63954In the Linux kernel, the following vulnerability has been resolved:
hpfs: fix a crash if hpfs_map_dnode_bitmap fails
If hpfs_map_dnode_bitmap fails, the code would call hpfs_brelse4 on
uninitialized quad buffer head, causing a crash.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-63955In the Linux kernel, the following vulnerability has been resolved:
mm/vmalloc: do not trigger BUG() on BH disabled context
__get_vm_area_node() currently triggers a BUG() if in_interrupt() returns
true. However, in_interrupt() also reports true when BH are disabled.
The bridge code can call rhashtable_lookup_insert_fast() with bottom
halves disabled:
__vlan_add()
-> br_fdb_add_local()
spin_lock_bh(&br->hash_lock); <-- Disable BH
-> fdb_add_local()
-> fdb_create()
-> rhashtable_lookup_insert_fast()
-> kvmalloc()
-> vmalloc()
-> __get_vm_area_node()
-> BUG_ON(in_interrupt())
spin_unlock_bh(&br->hash_lock)
this triggers the BUG() despite the caller not being in NMI or
hard IRQ context.
Replace the in_interrupt() check with in_nmi() || in_hardirq().Analyse NVD en cours Élevée CVSS 7.5 CVE-2026-63968In the Linux kernel, the following vulnerability has been resolved:
ipv6: fix possible infinite loop in fib6_select_path()
Found while auditing the same pattern Sashiko reported in
rt6_fill_node() [1]. Apply the same fix as
commit f8d8ce1b515a ("ipv6: fix possible infinite loop in fib6_info_uses_dev()").
Writers holding tb6_lock can list_del_rcu(&first->fib6_siblings)
without waiting for RCU readers; first->fib6_siblings.next then
still points into the old ring and this softirq-side walker never
reaches &first->fib6_siblings as its terminator. fib6_purge_rt()
always WRITE_ONCE()s first->fib6_nsiblings to 0 before
list_del_rcu(), so an inside-loop check is a reliable detach signal.
[1] https://sashiko.dev/#/patchset/20260526020227.4857-1-jiayuan.chen%40linux.devAnalyse NVD en cours Élevée CVSS 7.5 CVE-2026-63970In the Linux kernel, the following vulnerability has been resolved:
vsock/virtio: bind uarg before filling zerocopy skb
virtio_transport_send_pkt_info() allocates or reuses the zerocopy uarg
before entering the send loop, but virtio_transport_alloc_skb() still
fills the skb before it inherits that uarg. When fixed-buffer vectored
zerocopy hits MAX_SKB_FRAGS, io_sg_from_iter() may partially attach
managed frags and return -EMSGSIZE. The rollback path call kfree_skb()
to free an skb that carries SKBFL_MANAGED_FRAG_REFS but no uarg, so
skb_release_data() falls through to ordinary frag unref.
Pass the uarg into virtio_transport_alloc_skb() and bind it immediately
before virtio_transport_fill_skb(). This keeps control or no-payload skbs
untouched while ensuring success and rollback share one lifetime rule.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-63971In the Linux kernel, the following vulnerability has been resolved:
sctp: fix race between sctp_wait_for_connect and peeloff
sctp_wait_for_connect() drops and re-acquires the socket lock while
waiting for the association to reach ESTABLISHED state. During this
window, another thread can peeloff the association to a new socket via
getsockopt(SCTP_SOCKOPT_PEELOFF), changing asoc->base.sk. After
re-acquiring the old socket lock, sctp_wait_for_connect() returns
success without noticing the migration — the caller then accesses
the association under the wrong lock in sctp_datamsg_from_user().
Add the same sk != asoc->base.sk check that sctp_wait_for_sndbuf()
already has, returning an error if the association was migrated while
we slept.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-63972In the Linux kernel, the following vulnerability has been resolved:
net: mana: Skip redundant detach on already-detached port
When mana_per_port_queue_reset_work_handler() runs after a previous
detach succeeded but attach failed, the port is left in a detached
state with apc->tx_qp and apc->rxqs already freed. Calling
mana_detach() again unconditionally leads to NULL pointer dereferences
during queue teardown.
Add an early exit in mana_detach() when the port is already in
detached state (!netif_device_present) for non-close callers, making
it safe to call idempotently. This allows the queue reset handler and
other recovery paths to simply retry mana_attach() without redundant
teardown.Analyse NVD en cours Élevée CVSS 7.5 CVE-2026-63974In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: Set HCI_CMD_DRAIN_WORKQUEUE during device close
Since hci_dev_close_sync() can now be called during the reset path, we
should also set HCI_CMD_DRAIN_WORKQUEUE. This avoids queuing timeouts
while the hdev workqueue is being drained.Analyse NVD en cours Élevée CVSS 8.8 CVE-2026-63975In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix possible crash on l2cap_ecred_conn_rsp
If dcid is received for an already-assigned destination CID the spec
requires that both channels to be discarded, but calling l2cap_chan_del
may invalidate the tmp cursor created by list_for_each_entry_safe and
in fact it is the wrong procedure as the chan->dcid may be assigned
previously it really needs to be disconnected.
Calling l2cap_chan_clone directly may still lead to l2cap_chan_del so
instead schedule l2cap_chan_timeout with delay 0 to close the channel
asynchronously.Analyse NVD en cours Élevée CVSS 8.8 CVE-2026-63976In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: l2cap: clear chan->ident on ECRED reconfiguration success
l2cap_ecred_reconf_rsp() returns early on success without clearing
chan->ident. Every other L2CAP response handler (l2cap_ecred_conn_rsp,
l2cap_le_connect_rsp, l2cap_config_rsp) clears chan->ident after a
successful transaction to prevent the channel from matching subsequent
responses with the recycled ident value.
A remote attacker that completed a reconfiguration as the peer can
replay a failure response with the stale ident, causing the kernel to
match and destroy the already-established channel via
l2cap_chan_del(chan, ECONNRESET).
Clear chan->ident for all matching channels on success, and harden the
failure path by using l2cap_chan_hold_unless_zero() consistent with
other L2CAP handlers (l2cap_le_command_rej, __l2cap_get_chan_by_ident).Analyse NVD en cours Élevée CVSS 8.8 CVE-2026-63977In the Linux kernel, the following vulnerability has been resolved:
dpll: zl3073x: use __dpll_device_change_ntf() and remove change_work
The change_work was introduced to send device change notifications
from DPLL device callbacks without deadlocking on dpll_lock, since
the callbacks are already invoked under that lock. Now that
__dpll_device_change_ntf() is exported for callers that already
hold dpll_lock, use it directly and remove the change_work
infrastructure entirely.
This eliminates a race condition where change_work could be
re-scheduled after cancel_work_sync() during device teardown,
potentially causing the handler to dereference a freed or NULL
dpll_dev pointer.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-63978In the Linux kernel, the following vulnerability has been resolved:
net/handshake: Drain pending requests at net namespace exit
The arguments to list_splice_init() in handshake_net_exit() are
reversed. The call moves the local empty "requests" list onto
hn->hn_requests, leaving the local list empty, so the subsequent
drain loop runs zero iterations. Pending handshake requests that
had not yet been accepted are not torn down when the net namespace
is destroyed; each one keeps a reference on a socket file and on
the handshake_req allocation.
Pass the source and destination in the documented order
(list_splice_init(list, head) moves list onto head) so the pending
list is transferred to the local scratch list and drained through
handshake_complete().
Fixing the splice direction exposes a list-corruption race. After
the splice each req->hr_list still has non-empty link pointers,
threading the stack-local scratch list rather than hn_requests.
A concurrent handshake_req_cancel() -- for example, from sunrpc's
TLS timeout on a kernel socket whose netns reference was not
taken -- finds the request through the rhashtable, calls
remove_pending(), and sees !list_empty(&req->hr_list).
__remove_pending_locked() then list_del_init()s an entry off the
scratch list while the drain iterates, corrupting it. The same
call arriving after the drain loop has run list_del() on an
entry hits LIST_POISON instead.
Have remove_pending() check HANDSHAKE_F_NET_DRAINING under
hn_lock and report not-found when drain is in progress. The
drain has already taken ownership; handshake_complete()'s existing
test_and_set on HANDSHAKE_F_REQ_COMPLETED still arbitrates
between drain and cancel for who calls the consumer's hp_done. Use
list_del_init() rather than list_del() in the drain so req->hr_list
does not carry LIST_POISON after drain releases the entry.
The DRAINING guard in remove_pending() makes cancel return false,
but cancel still falls through to test_and_set_bit on
HANDSHAKE_F_REQ_COMPLETED and drops the request's hr_file reference.
Without another pin, if that is the last reference, sk_destruct frees
the request while it is still linked on the drain loop's local list.
Pin each request's hr_file under hn_lock before releasing the list,
and drop that drain pin after the loop finishes with the request.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-63979In the Linux kernel, the following vulnerability has been resolved:
net/handshake: hand off the pinned file reference to accept_doit
handshake_req_next() removes the request from the per-net
pending list and drops hn_lock before handshake_nl_accept_doit()
reads req->hr_sk->sk_socket and dereferences sock->file (once in
FD_PREPARE() and again in get_file()). In that window a
consumer running tls_handshake_cancel() followed by sockfd_put()
(svc_sock_free) or __fput_sync() (xs_reset_transport) releases
sock->file. sock_release() then runs sock_orphan(), zeroing
sk_socket, and frees the struct socket. The accept-side code
either reads NULL through sk_socket or chases freed memory.
The submit-side sock_hold() does not prevent this. sk_refcnt
protects struct sock, but struct socket and sock->file are
independently refcounted via the file descriptor the consumer
owns. Pinning sk leaves sock and sock->file unprotected.
Retarget the accept-side dereferences at req->hr_file, which was
pinned at submit time, instead of req->hr_sk->sk_socket->file.
Pinning on its own is not sufficient: a consumer that cancels
between handshake_req_next() returning and accept_doit reaching
FD_PREPARE() takes the !remove_pending() branch in
handshake_req_cancel() and drops hr_file before the accept side
takes its own reference. Hand off an additional file reference
inside handshake_req_next(), under hn_lock, so the accept side
operates on a reference that no concurrent handshake_req_cancel()
can revoke. FD_PREPARE() consumes that handed-off reference,
either by transferring it to the new fd in fd_publish() or by
dropping it in the cleanup destructor on error; the explicit
get_file() that previously balanced FD_PREPARE() is therefore
redundant and goes away.
Update handshake_req_cancel_test2 and _test3 to simulate the
FD_PREPARE() consumption with an fput() so the kunit file-count
assertions stay balanced.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-63980In the Linux kernel, the following vulnerability has been resolved:
net/handshake: Use spin_lock_bh for hn_lock
nvmet_tcp_state_change(), a socket callback that runs in BH context,
can reach handshake_req_cancel() via nvmet_tcp_schedule_release_queue()
and tls_handshake_cancel(). handshake_req_cancel() acquires
hn->hn_lock with plain spin_lock(). If a process-context thread on
the same CPU holds hn->hn_lock when a softirq invokes the cancel path,
the lock attempt deadlocks. This is the only caller that invokes
tls_handshake_cancel() from BH context; every other consumer calls it
from process context.
Deferring the cancel to process context in the NVMe target is not
straightforward: nvmet_tcp_schedule_release_queue() must call
tls_handshake_cancel() atomically with its state transition to
DISCONNECTING. If the cancel were deferred, the handshake completion
callback could fire in the window before the cancel runs, observe the
unexpected state, and return without dropping its kref on the queue.
Reworking that interlock is considerably more invasive than hardening
the handshake lock. Convert all hn->hn_lock acquisitions from
spin_lock/spin_unlock to spin_lock_bh/spin_unlock_bh so the lock is
never taken with softirqs enabled.Analyse NVD en cours Élevée CVSS 7.5 CVE-2026-63984In the Linux kernel, the following vulnerability has been resolved:
ipv6: rpl: fix hdrlen overflow in ipv6_rpl_srh_decompress()
ipv6_rpl_srh_decompress() computes:
outhdr->hdrlen = (((n + 1) * sizeof(struct in6_addr)) >> 3);
hdrlen is __u8. For n >= 127 the result exceeds 255 and silently
truncates. With n=127 (cmpri=15, cmpre=15, pad=0, hdrlen=16):
(128 * 16) >> 3 = 256, truncated to 0 as __u8
The caller in ipv6_rpl_srh_rcv() then places the compressed header
at buf + ((ohdr->hdrlen + 1) << 3). With hdrlen=0 this is buf + 8,
but the decompressed region occupies buf[0..2055] (8-byte header
plus 128 full addresses). The compressed header overlaps the
decompressed data, and ipv6_rpl_srh_compress() writes into this
overlap, corrupting the routing header of the forwarded packet.
The existing guard at exthdrs.c:546 checks (n + 1) > 255, which
prevents n+1 from overflowing unsigned char (the segments_left
field), but does not prevent the computed hdrlen from overflowing
__u8. n=127 passes because 128 <= 255, yet hdrlen=256 does not
fit.
Tighten the bound to (n + 1) > 127. This caps n at 126, giving
hdrlen = (127 * 16) >> 3 = 254, which fits in __u8. The compressed
header then lands at buf + ((254 + 1) << 3) = buf + 2040, exactly
past the decompressed region (buf[0..2039]). No overlap. 127
segments is well beyond any realistic RPL deployment.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-63985In the Linux kernel, the following vulnerability has been resolved:
ethtool: eeprom: add more safeties to EEPROM Netlink fallback
The Netlink fallback path for reading module EEPROM
(fallback_set_params()) validates that offset < eeprom_len,
but does not check that offset + length stays within eeprom_len.
The ioctl equivalent (ethtool_get_any_eeprom() in ioctl.c) has
always enforced both bounds:
if (eeprom.offset + eeprom.len > total_len)
return -EINVAL;
This could lead to surprises in both drivers and device FW.
Add the missing offset + length validation to fallback_set_params(),
mirroring the ioctl.
Similarly - ethtool core in general, and ethtool_get_any_eeprom()
in particular tries to zero-init all buffers passed to the drivers
to avoid any extra work of zeroing things out. eeprom_fallback()
uses a plain kmalloc(), change it to zalloc.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-63987In the Linux kernel, the following vulnerability has been resolved:
ethtool: coalesce: cap profile updates at NET_DIM_PARAMS_NUM_PROFILES
ethnl_update_profile() walks the ETHTOOL_A_PROFILE_IRQ_MODERATION
nest list with an index 'i' and writes new_profile[i++] without
bounding i. The destination is kmemdup()'d at NET_DIM_PARAMS_NUM_PROFILES
entries (5), but the Netlink nest count is entirely user-controlled.
Netlink policies do not have support for constraining the number
of nested entries (or number of multi-attr entries).Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-63992In the Linux kernel, the following vulnerability has been resolved:
tunnels: do not assume transport header in iptunnel_pmtud_check_icmp()
In some cases, iptunnel_pmtud_check_icmp() can be called while
skb transport header is not set.
This triggers an out-of-bound access, because
(typeof(skb->transport_header))~0U is 65535.
Access the icmp header based on IPv4 network header,
after making sure icmp->type is present in skb linear part.
Note that iptunnel_pmtud_check_icmpv6()) is fine.Analyse NVD en cours Critique CVSS 9.1 CVE-2026-63993In the Linux kernel, the following vulnerability has been resolved:
vxlan: do not reuse cached ip_hdr() value after skb_tunnel_check_pmtu()
skb_tunnel_check_pmtu() can change skb->head.
Reusing old_iph afer skb_tunnel_check_pmtu() can cause an UAF.
Use instead ip_hdr(skb) as done in drivers/net/bareudp.c
and drivers/net/geneve.c.
Found by Sashiko.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-63994In the Linux kernel, the following vulnerability has been resolved:
tunnels: load network headers after skb_cow() in iptunnel_pmtud_build_icmp[v6]()
Sashiko found that iptunnel_pmtud_build_icmp() and
iptunnel_pmtud_build_icmpv6() were caching ip_hdr() and ipv6_hdr()
before an skb_cow() call which can reallocate skb->head.
Fix this possible UAF by initializing the local variables
after the skb_cow() call.
Remove skb_reset_network_header() calls which were not needed.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-63995In the Linux kernel, the following vulnerability has been resolved:
ethtool: cmis: validate start_cmd_payload_size from module
The CMIS firmware update code reads start_cmd_payload_size from
the module's FW Management Features CDB reply and uses it directly
as the byte count for memcpy. The destination buffer is 112 bytes
(ETHTOOL_CMIS_CDB_LPL_MAX_PL_LENGTH - 8). So a malicious
module (or corrupted response) can cause a OOB write later on in
cmis_fw_update_start_download().
Let's error out. If modules that expect longer LPL writes actually
exist we should revisit.
struct cmis_cdb_start_fw_download_pl's definition has to move,
no change there.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-63996In the Linux kernel, the following vulnerability has been resolved:
ethtool: cmis: require exact CDB reply length
Malicious SFP module could respond with rpl_len longer than
what cmis_cdb_process_reply() expected, leading to OOB writes.
Malicious HW is a bit theoretical but some modules may just
be buggy and/or the reads may occasionally get corrupted,
so let's protect the kernel.
The existing check protects from short replies. We need to
protect from long ones, too. All callers that pass a non-zero
rpl_exp_len cast the reply payload to a fixed-layout struct
and read fields at fixed offsets, with no version negotiation
or short-reply handling:
- cmis_cdb_validate_password()
- cmis_cdb_module_features_get()
- cmis_fw_update_fw_mng_features_get()
so let's assume that responses longer than expected do not
have to be handled gracefully here. Add a warning message
to make the debug easier in case my understanding is wrong...
Note that page_data->length (argument of kmalloc) comes from
last arg to ethtool_cmis_page_init() which is rpl_exp_len.
Note2 that AIs also like to point out overflows in args->req.payload
itself (which is a fixed-size 120 B buffer, on the stack),
but callers should be reading structs defined by the standard,
so protecting from requests for more data than max seem like
defensive programming.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64000In the Linux kernel, the following vulnerability has been resolved:
net: hsr: fix potential OOB access in supervision frame handling
Ensure the entire TLV header is linearized before access by adding
sizeof(struct hsr_sup_tlv) to the pskb_may_pull() calls. Without this,
a truncated frame could cause an out-of-bounds access.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64002In the Linux kernel, the following vulnerability has been resolved:
ipv4: free net->ipv4.sysctl_local_reserved_ports after unregister_net_sysctl_table()
ipv4_sysctl_exit_net() is currently freeing net->ipv4.sysctl_local_reserved_ports
too soon.
Only after unregister_net_sysctl_table() we can be sure no threads can possibly
use the sysctls, including /proc/sys/net/ipv4/ip_local_reserved_ports.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64003In the Linux kernel, the following vulnerability has been resolved:
scsi: core: Run queues for all non-SDEV_DEL devices from scsi_run_host_queues
While a SCSI host is in a recovery state, scsi_mq_requeue_cmd() will not
set the requeue list for a requeued command to be kicked in the future.
The expectation is a call to scsi_run_host_queues() will kick all SCSI
devices once the recovery state is cleared.
However, scsi_run_host_queues() uses shost_for_each_device() which uses
scsi_device_get() and so will ignore devices in a partially removed
state like SDEV_CANCEL. But these devices may also have requeued
requests, leaving their requests stuck from not being kicked and causing
the removal process of the device to hang.
scsi_run_host_queues() needs to run against more devices than the macro
shost_for_each_device() allows. Instead of using the too limiting
scsi_device_get() state checks, only ignore devices in SDEV_DEL state or
when unable to acquire a reference. Attempt to run the queues for all
other devices when scsi_run_host_queues() is called.Analyse NVD en cours Élevée CVSS 7.5 CVE-2026-64004In the Linux kernel, the following vulnerability has been resolved:
net/iucv: fix locking in .getsockopt
Mirror iucv_sock_setsockopt() and wrap the whole switch in
lock_sock()/release_sock(). The pre-existing SO_MSGLIMIT-only lock
becomes redundant and is removed.
Any AF_IUCV HIPER user can potentially crash the kernel by racing
recvmsg() with getsockopt(SO_MSGSIZE): the SO_MSGSIZE arm dereferences
iucv->hs_dev->mtu after iucv_sock_close() (called from the racing
recvmsg()) has set hs_dev to NULL, producing a NULL pointer dereference
oops.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64005In the Linux kernel, the following vulnerability has been resolved:
net/smc: Do not re-initialize smc hashtables
INIT_HLIST_HEAD(&smc_v*_hashinfo.ht) are called after smc_nl_init(),
proto_register() and sock_register(). This can lead to smc_v*_hashinfo.ht
being reset even though hash entries already exist and are being used,
possibly resulting in a corrupted list.
Remove unnecessary and dangerous re-initialisation of smc_v*_hashinfo.ht in
smc_init(); it is implicitly initialised to zero anyhow. Add
HLIST_HEAD_INIT to the definitions for clarity.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64007In the Linux kernel, the following vulnerability has been resolved:
netfilter: synproxy: refresh tcphdr after skb_ensure_writable
synproxy_tstamp_adjust() rewrites the TCP timestamp option in place
and then patches the TCP checksum via inet_proto_csum_replace4() on
the caller-supplied tcphdr pointer. Both ipv4_synproxy_hook() and
ipv6_synproxy_hook() obtain that pointer with skb_header_pointer()
before calling in, so it may either alias skb->head directly or
point at the caller's on-stack _tcph buffer.
Between obtaining the pointer and using it, the function calls
skb_ensure_writable(skb, optend), which on a cloned or non-linear
skb invokes pskb_expand_head() and frees the old skb->head. After
that point the cached th is stale:
caller (ipv[46]_synproxy_hook)
th = skb_header_pointer(skb, ..., &_tcph)
synproxy_tstamp_adjust(skb, protoff, th, ...)
skb_ensure_writable(skb, optend)
pskb_expand_head() /* kfree(old skb->head) */
...
inet_proto_csum_replace4(&th->check, ...)
/* writes into freed head, or
into the caller's stack copy
leaving the on-wire checksum
stale */
The option bytes are written through skb->data and are fine; only
the checksum update goes through th and so lands in the wrong
place. The result is either a write into freed slab memory or a
packet leaving with a checksum that does not match its payload.
Fix by re-deriving th from skb->data + protoff immediately after
skb_ensure_writable() succeeds, so the subsequent checksum update
targets the linear, writable header.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64008In the Linux kernel, the following vulnerability has been resolved:
accel/rocket: fix UAF via dangling GEM handle in create_bo
rocket_ioctl_create_bo() inserts a GEM handle into the file's IDR via
drm_gem_handle_create() early on, then performs several operations that
can fail (sgt allocation, drm_mm insert, iommu_map). If any fail after
the handle is live, the error path calls drm_gem_shmem_object_free()
which kfree's the object without removing the handle from the IDR.
This leaves a dangling handle pointing to freed slab memory. Any
subsequent ioctl using that handle (PREP_BO, FINI_BO, SUBMIT) calls
drm_gem_object_lookup() and dereferences freed memory (UAF).
Fix by moving drm_gem_handle_create() to after all fallible operations
succeed, matching the pattern used by panfrost, lima, and etnaviv.
Also fix drm_mm_insert_node_generic() whose return value was silently
overwritten by iommu_map_sgtable() on the next line. Add the missing
error check.
[tomeu: Move handle creation to the very end]Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64009In the Linux kernel, the following vulnerability has been resolved:
xfrm: Check for underflow in xfrm_state_mtu
Leo Lin reported OOB write issue in esp component:
xfrm_state_mtu() returns u32 but performs its arithmetic in unsigned
modulo-2^32 space using an attacker-influenced "header_len + authsize +
net_adj" subtracted from a small "mtu" argument. A nobody user can
install an IPv4 ESP tunnel SA with a large authentication key
(XFRMA_ALG_AUTH_TRUNC, e.g. hmac(sha512), 64-byte key, 64-byte trunc),
configure a small interface MTU (68 bytes), and set XFRMA_TFCPAD to a
large value. When a single UDP datagram is then sent through the
tunnel, xfrm_state_mtu() underflows to a near-2^32 value, and
esp_output() consumes it as a signed int via:
padto = min(x->tfcpad, xfrm_state_mtu(x, mtu_cached))
esp.tfclen = padto - skb->len (assigned to int)
esp.tfclen ends up negative (e.g. -207). It is sign-extended to size_t
when passed to memset() inside esp_output_fill_trailer(), producing a
~16 EB write of zeroes at skb_tail_pointer(skb). KASAN logs it as
"Write of size 18446744073709551537 at addr ffff888...".
Check for underflow and return 1. This causes the sendmsg attempt to
fail with ENETUNREACH.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64010In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: Fix use-after-free race in nfc_llcp_recv_cc()
A race condition exists in the NFC LLCP connection state machine where
the connection acceptance packet (CC) can be processed concurrently with
socket release. This can lead to a use-after-free of the socket object.
When nfc_llcp_recv_cc() moves the socket from the connecting_sockets
list to the sockets list, it does so without holding the socket lock.
If llcp_sock_release() is executing concurrently, it might have already
unlinked the socket and dropped its references, which can result in
nfc_llcp_recv_cc() linking a freed socket into the live list.
Fix this by holding lock_sock() during the state transition and list
movement in nfc_llcp_recv_cc(). After acquiring the lock, check if
the socket is still hashed to ensure it hasn't already been unlinked
and marked for destruction by the release path. This aligns the locking
pattern with recv_hdlc() and recv_disc().Analyse NVD en cours Élevée CVSS 8.8 CVE-2026-64011In the Linux kernel, the following vulnerability has been resolved:
nfc: llcp: Fix use-after-free in llcp_sock_release()
llcp_sock_release() unconditionally unlinks the socket from the local
sockets list. However, if the socket is still in connecting state, it
is on the connecting list.
Fix this by checking the socket state and unlinking from the correct list.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64015In the Linux kernel, the following vulnerability has been resolved:
security/keys: fix missed RCU read section on lookup
Nicholas Carlini reports that the keyring code calls assoc_array_find()
in find_key_to_update() without holding the RCU read lock, while the
assoc_array_gc() code really is designed around removing the node from
the tree and then freeing it after an RCU grace-period.
The regular key handling doesn't see this because holding the keyring
semaphore hides any lifetime issues, but the persistent key handling
uses a different model.
Instead of extending the keyring locking, just do the simple RCU locking
that the assoc_array was designed for.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64016In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix durable reconnect error path file lifetime
After a durable reconnect succeeds, ksmbd_reopen_durable_fd() republishes
the same ksmbd_file into the session volatile-id table. If smb2_open()
then takes a later error path, cleanup first calls ksmbd_fd_put(work, fp)
and then unconditionally calls ksmbd_put_durable_fd(dh_info.fp).
In this case fp and dh_info.fp are the same object. The first put drops the
reconnect lookup reference, but the final durable put can run
__ksmbd_close_fd(NULL, fp). Because the final close is not session-aware,
it can free the file object without removing the volatile-id entry that was
just published into the session table.
Use the session-aware put for the final reconnect drop when the reconnect
had already succeeded and the error path is cleaning up the republished
file. Earlier reconnect failures, before fp is assigned to dh_info.fp, keep
using the durable-only put path.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64017In the Linux kernel, the following vulnerability has been resolved:
blk-mq: pop cached request if it is usable
When submitting a bio to blk-mq, if the task should sleep after peeking
a cached request, but before it pops it, the plug flushes and calls
blk_mq_free_plug_rqs, freeing the cached_rqs. This creates a
use-after-free bug. Fix this by popping the cached request before any
possible blocking calls if it is suitable for use.
Popping this request first holds a queue reference, so avoid any
serialization races with queue freezes and can safely proceed with
dispatching that request to the driver. This potentially increases a
timing window from when a driver wants to freeze its queue to when
requests stop being dispatched. That scenario is off the fast path
though, and drivers need to appropriately handle requests during a
freeze request anyway.
The downside is the popped element needs to be individually freed when
we performed a bio plug merge. The cached request would have had to be
freed later anyway, but this patch does it inline with building the plug
list instead of after flushing it.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64018In the Linux kernel, the following vulnerability has been resolved:
net: mana: validate rx_req_idx to prevent out-of-bounds array access
In mana_hwc_rx_event_handler(), rx_req_idx is derived from
sge->address in DMA-coherent memory. In Confidential VMs
(SEV-SNP/TDX), this memory is shared unencrypted and HW can modify
WQE contents at any time. No bounds check exists on rx_req_idx,
which can lead to an out-of-bounds access into reqs[].
Add bounds check on rx_req_idx in mana_hwc_rx_event_handler() before
using it to index the reqs[] array.Analyse NVD en cours Critique CVSS 9.3 CVE-2026-64020In the Linux kernel, the following vulnerability has been resolved:
nvme-pci: fix dma_vecs leak on p2p memory
We don't unmap P2P memory, so we don't need to track it. The dma_vec
allocation was getting leaked on the completion.Analyse NVD en cours Élevée CVSS 7.5 CVE-2026-64023In the Linux kernel, the following vulnerability has been resolved:
gpio: aggregator: fix a potential use-after-free
On error we free aggr->lookups->dev_id before removing the entry from
the lookup table. If a concurrent thread calls gpiod_find() before we
remove the entry, it could iterate over the list and call
gpiod_match_lookup_table() which unconditionally dereferences dev_id
when calling strcmp(). Reverse the order of cleanup.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64024In the Linux kernel, the following vulnerability has been resolved:
tcp: fix stale per-CPU tcp_tw_isn leak enabling ISN prediction
Blamed commit moved the TIME_WAIT-derived ISN from the skb control
block to a per-CPU variable, assuming the value would always be consumed
by tcp_conn_request() for the same packet that wrote it. That assumption
is violated by multiple drop paths between the producer
(__this_cpu_write(tcp_tw_isn, isn) in tcp_v{4,6}_rcv()) and the consumer
(tcp_conn_request()):
- min_ttl / min_hopcount check
- xfrm policy check
- tcp_inbound_hash() MD5/AO mismatch
- tcp_filter() eBPF/SO_ATTACH_FILTER drop
- th->syn && th->fin discard in tcp_rcv_state_process() TCP_LISTEN
- psp_sk_rx_policy_check() in tcp_v{4,6}_do_rcv()
- tcp_checksum_complete() in tcp_v{4,6}_do_rcv()
- tcp_v{4,6}_cookie_check() returning NULL
When a packet is dropped on any of these paths, tcp_tw_isn is left set.
The next SYN processed on the same CPU then consumes the non zero value in
tcp_conn_request(), receiving a potentially predictable ISN.
This patch moves back tcp_tw_isn to skb->cb[], getting rid of the per-cpu
variable.
Note that tcp_v{4,6}_fill_cb() do not set it.
Very litle impact on overall code size/complexity:
$ scripts/bloat-o-meter -t vmlinux.old vmlinux.new
add/remove: 0/0 grow/shrink: 2/1 up/down: 8/-15 (-7)
Function old new delta
tcp_v6_rcv 3038 3042 +4
tcp_v4_rcv 3035 3039 +4
tcp_conn_request 2938 2923 -15
Total: Before=24436060, After=24436053, chg -0.00%Analyse NVD en cours Critique CVSS 9.4 CVE-2026-64025In the Linux kernel, the following vulnerability has been resolved:
bpf, skmsg: fix verdict sk_data_ready racing with ktls rx
sk_psock_strp_data_ready() already checks tls_sw_has_ctx_rx() and
defers to psock->saved_data_ready when a TLS RX context is present,
avoiding a conflict with the TLS strparser's ownership of the receive
queue (commit e91de6afa81c, "bpf: Fix running sk_skb program types
with ktls").
sk_psock_verdict_data_ready() has no equivalent guard. When a socket
is inserted into a sockmap (BPF_SK_SKB_VERDICT) before TLS RX is
configured, tls_sw_strparser_arm() saves sk_psock_verdict_data_ready
as rx_ctx->saved_data_ready. On data arrival:
tls_data_ready -> tls_strp_data_ready -> tls_rx_msg_ready
-> saved_data_ready() = sk_psock_verdict_data_ready()
-> tcp_read_skb() drains sk_receive_queue via __skb_unlink()
without calling tcp_eat_skb(), so copied_seq is not advanced.
tls_strp_msg_load() then finds tcp_inq() >= full_len (stale), calls
tcp_recv_skb() on the now-empty queue, hits WARN_ON_ONCE(!first), and
returns with rx_ctx->strp.anchor.frag_list pointing at a psock-owned
(potentially freed) skb. tls_decrypt_sg() subsequently walks that
frag_list: use-after-free.
Apply the same fix as sk_psock_strp_data_ready(): if a TLS RX context
is present, call psock->saved_data_ready (sock_def_readable) to wake
recv() waiters and return immediately, leaving the receive queue
untouched. TLS retains sole ownership of the queue and decrypts the
record normally through tls_sw_recvmsg().Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64026In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix DATA decrypt vs splice() by copying data to buffer in recvmsg
This improves the fix for CVE-2026-43500.
Fix the pagecache corruption from in-place decryption of a DATA packet
transmitted locally by splice() by getting rid of the packet sharing in the
I/O thread and unconditionally extracting the packet content into a bounce
buffer in which the buffer is decrypted. recvmsg() (or the kernel
equivalent) then copies the data from the bounce buffer to the destination
buffer. The sk_buff then remains unmodified.
This has an additional advantage in that the packet is then arranged in the
buffer with the correct alignment required for the crypto algorithms to
process directly. The performance of the crypto does seem to be a little
faster and, surprisingly, the unencrypted performance doesn't seem to
change much - possibly due to removing complexity from the I/O thread.
Yet another advantage is that the I/O thread doesn't have to copy packets
which would slow down packet distribution, ACK generation, etc..
The buffer belongs to the call and is allocated initially at 2K,
sufficiently large to hold a whole jumbo subpacket, but the buffer will be
increased in size if needed. However, to take this work, MSG_PEEK may
cause a later packet to be decrypted into the buffer, in which case the
earlier one will need re-decrypting for a subsequent recvmsg().
Note that rx_pkt_offset may legitimately see 0 as a valid offset now, so
switch to using USHRT_MAX to indicate an invalid offset.
Note also that I would generally prefer to replace the buffers of the
current sk_buff with a new kmalloc'd buffer of the right size, ditching the
old data and frags as this makes the handling of MSG_PEEK easier and
removes the re-decryption issue, but this looks like quite a complicated
thing to achieve. skb_morph() looks half way to what I want, but I don't
want to have to allocate a new sk_buff.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64027In the Linux kernel, the following vulnerability has been resolved:
net: shaper: rework the VALID marking (again)
Recent commit changed the semantics from NOT_VALID to VALID.
I didn't realize that the flags are not stored atomically
with the entry in XArray. There's still a race of reader
observing a VALID mark for a slot, getting interrupted,
writer replacing the entry with a different one, reader
continuing, fetching the entry which is now a different
pointer than the pointer for which VALID was meant.
The biggest consequence of this is that we may see a UAF
since net_shaper_rollback() assumed that entries without
VALID can be freed without observing RCU.
Looks like the XArray marks are buying us nothing at this
point. Let's convert the code to an explicit valid field.
The smp_load_acquire() / smp_store_release() barriers are
marginally cleaner.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64029In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: Serialize UMP output teardown with event_input
seq_ump_process_event() borrows client->out_rfile.output without
synchronizing with the first-open and last-close transition in
seq_ump_client_open() and seq_ump_client_close().
The last output unuse can therefore drop opened[STR_OUT] to zero and
release the rawmidi file while an in-flight event_input callback is still
inside snd_rawmidi_kernel_write(). That leaves the rawmidi substream
runtime exposed to teardown before the write path has taken its own
buffer reference.
Add a per-client rwlock for the event_input-visible output file. Publish
a newly opened output file under the write side, and hold the read side
from the output lookup through snd_rawmidi_kernel_write(). The last
output close copies and clears the visible output file under the write
side, then drops the lock and releases the saved rawmidi file. Use
IRQ-safe rwlock guards because event_input can also be reached from
atomic sequencer delivery.
The buggy scenario involves two paths, with each column showing the
order within that path:
path A label: event_input path path B label: last unuse path
1. seq_ump_process_event() reads 1. seq_ump_client_close()
client->out_rfile.output. drops opened[STR_OUT] to zero.
2. snd_rawmidi_kernel_write1() 2. snd_rawmidi_kernel_release()
has not yet pinned runtime. closes the output file.
3. The writer continues using 3. close_substream() frees
the borrowed substream. substream->runtime.
This keeps the output substream and runtime alive for the full
event_input write while keeping rawmidi release outside the rwlock.
KASAN reproduced this as a slab-use-after-free in
snd_rawmidi_kernel_write1(), with allocation through
seq_ump_use()/snd_seq_port_connect() and free through
seq_ump_unuse()/snd_seq_port_disconnect().
Validation reproduced this kernel report:
KASAN slab-use-after-free in snd_rawmidi_kernel_write1+0x9d/0x400
RIP: 0033:0x7f5528af837f
Read of size 8
Call trace:
dump_stack_lvl+0x73/0xb0 (?:?)
print_report+0xd1/0x650 (?:?)
srso_alias_return_thunk+0x5/0xfbef5 (?:?)
__virt_addr_valid+0x1a7/0x340 (?:?)
kasan_complete_mode_report_info+0x64/0x200 (?:?)
kasan_report+0xf7/0x130 (?:?)
snd_rawmidi_kernel_write1+0x9d/0x400 (?:?)
__asan_load8+0x82/0xb0 (?:?)
update_stack_state+0x1ef/0x2d0 (?:?)
snd_rawmidi_kernel_write+0x1a/0x20 (?:?)
seq_ump_process_event+0xd4/0x120 (sound/core/seq/seq_ump_client.c:82)
__snd_seq_deliver_single_event+0x8a/0xe0 (?:?)
snd_seq_deliver_from_ump+0x2b2/0xd60 (?:?)
lock_acquire+0x14e/0x2e0 (?:?)
find_held_lock+0x31/0x90 (?:?)
snd_seq_port_use_ptr+0xa6/0xe0 (?:?)
__kasan_check_write+0x18/0x20 (?:?)
do_raw_read_unlock+0x32/0xa0 (?:?)
_raw_read_unlock+0x26/0x50 (?:?)
snd_seq_deliver_single_event+0x45c/0x4b0 (?:?)
snd_seq_deliver_event+0x10d/0x1b0 (?:?)
snd_seq_client_enqueue_event+0x192/0x240 (?:?)
snd_seq_write+0x2cd/0x450 (?:?)
apparmor_file_permission+0x20/0x30 (?:?)
security_file_permission+0x51/0x60 (?:?)
vfs_write+0x1ce/0x850 (?:?)
__fget_files+0x12b/0x220 (?:?)
lock_release+0xc8/0x2a0 (?:?)
__rcu_read_unlock+0x74/0x2d0 (?:?)
__fget_files+0x135/0x220 (?:?)
ksys_write+0x15a/0x180 (?:?)
rcu_is_watching+0x24/0x60 (?:?)
__x64_sys_write+0x46/0x60 (?:?)
x64_sys_call+0x7d/0x20d0 (?:?)
do_syscall_64+0xc1/0x360 (arch/x86/entry/syscall_64.c:87)
entry_SYSCALL_64_after_hwframe+0x77/0x7f (?:?)Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64030In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: bounds-check link_id in ieee80211_ml_epcs
IEEE80211_MLE_STA_EPCS_CONTROL_LINK_ID is 0x000f, so link_id extracted
from a PRIO_ACCESS ML element PER_STA_PROFILE subelement can be 0..15.
sdata->link[] has IEEE80211_MLD_MAX_NUM_LINKS (15) entries (indices 0..14),
making index 15 out-of-bounds.
A connected WiFi 7 AP can trigger this by sending an EPCS Enable Response
action frame with a PER_STA_PROFILE subelement where link_id = 15. The
unsolicited-notification path (dialog_token = 0) is reachable any time
EPCS is already enabled, without any prior client request.
sdata->link[15] reads into the first word of sdata->activate_links_work
(a wiphy_work whose embedded list_head is non-NULL after INIT_LIST_HEAD),
so the NULL check on the result does not catch the invalid access. The
garbage pointer is then passed to ieee80211_sta_wmm_params(), which
dereferences link->sdata and crashes the kernel.
The same class of bug was fixed for ieee80211_ml_reconfiguration() by
commit 162d331d833d ("wifi: mac80211: bounds-check link_id in
ieee80211_ml_reconfiguration").Analyse NVD en cours Élevée CVSS 8.8 CVE-2026-64031In the Linux kernel, the following vulnerability has been resolved:
erofs: fix managed cache race for unaligned extents
After unaligned compressed extents were introduced, the following race
could occur:
[Thread 1] [Thread 2]
(z_erofs_fill_bio_vec)
<handle a Z_EROFS_PREALLOCATED_FOLIO folio>
...
filemap_add_folio (1)
(z_erofs_bind_cache)
<the same folio is found..>
..
..
folio_attach_private (2)
filemap_add_folio (3) again
Since (1) is executed but (2) hasn't been executed yet, it's possible
that another thread finds the same managed folio in z_erofs_bind_cache()
for a different pcluster and calls filemap_add_folio() again since
folio->private is still Z_EROFS_PREALLOCATED_FOLIO.
Fix this by explicitly clearing folio->private before making the folio
visible in the managed cache so that another pcluster can simply wait
on the locked managed folio as what we did for other shared cases [1].
This only impacts unaligned data compression (`-E48bit` with zstd,
for example).
[1] Commit 9e2f9d34dd12 ("erofs: handle overlapped pclusters out of
crafted images properly") was originally introduced to handle crafted
overlapped extents, but it addresses unaligned extents as well.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64032In the Linux kernel, the following vulnerability has been resolved:
bridge: mcast: Fix a possible use-after-free when removing a bridge port
When per-VLAN multicast snooping is enabled, the bridge iterates over
all the bridge ports, disables the per-port multicast context on each
port and enables the per-{port, VLAN} multicast contexts instead. The
reverse happens when per-VLAN multicast snooping is disabled.
When global multicast snooping is enabled, the bridge iterates over all
the bridge ports and enables the per-port multicast context on each
port. The reverse happens when multicast snooping is disabled.
The above scheme can result in a situation where both types of contexts
(per-port and per-{port, VLAN}) are enabled on a single bridge port:
# ip link add name br1 up type bridge mcast_snooping 1 mcast_querier 1 vlan_filtering 1
# ip link add name dummy1 up master br1 type dummy
# ip link set dev br1 type bridge mcast_vlan_snooping 1
# ip link set dev br1 type bridge mcast_snooping 0
# ip link set dev br1 type bridge mcast_snooping 1
This is not intended and it is a problem since the commit cited below.
Prior to this commit, when removing a bridge port,
br_multicast_disable_port() would disable the per-port multicast context
and the per-{port, VLAN} multicast contexts would get disabled when
flushing VLANs.
After this commit, br_multicast_disable_port() only disables the
per-port multicast context if per-VLAN multicast snooping is disabled.
If both types of contexts were enabled on the port when it was removed,
the per-port multicast context would remain enabled when freeing the
bridge port, leading to a use-after-free [1].
Fix by preventing the bridge from enabling / disabling the per-port
multicast contexts when toggling global multicast snooping if per-VLAN
multicast snooping is enabled.
[1]
ODEBUG: free active (active state 0) object: ffff88810f8bda78 object type: timer_list hint: br_ip6_multicast_port_query_expired (net/bridge/br_multicast.c:1927)
WARNING: lib/debugobjects.c:629 at debug_print_object+0x1b1/0x3e0, CPU#5: swapper/5/0
[...]
Call Trace:
<IRQ>
__debug_check_no_obj_freed (lib/debugobjects.c:1116)
kfree (mm/slub.c:2620 mm/slub.c:6250 mm/slub.c:6565)
kobject_cleanup (lib/kobject.c:689)
rcu_do_batch (kernel/rcu/tree.c:2617)
rcu_core (kernel/rcu/tree.c:2869)
handle_softirqs (kernel/softirq.c:622)
__irq_exit_rcu (kernel/softirq.c:656 kernel/softirq.c:496 kernel/softirq.c:735)
irq_exit_rcu (kernel/softirq.c:752)
sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1061 (discriminator 47) arch/x86/kernel/apic/apic.c:1061 (discriminator 47))
</IRQ>Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64033In the Linux kernel, the following vulnerability has been resolved:
RDMA/rtrs: Fix use-after-free in path file creation cleanup
In the error path of rtrs_srv_create_path_files(), the sysfs root folders
may already have been created and srv_path->kobj may already have been
initialized. If a later step fails, the cleanup currently calls
kobject_put(&srv_path->kobj) before
rtrs_srv_destroy_once_sysfs_root_folders(srv_path).
kobject_put() may drop the last reference to srv_path->kobj and invoke the
release callback, rtrs_srv_release(), which frees srv_path. The following
call to rtrs_srv_destroy_once_sysfs_root_folders(srv_path) then
dereferences srv_path internally to access srv_path->srv, resulting in a
use-after-free.
This failure path is reached before rtrs_srv_create_path_files() returns
success, so the successful-path lifetime handling is not involved.
Fix this by destroying the sysfs root folders before calling
kobject_put(&srv_path->kobj), so srv_path is still valid while the helper
accesses it.
This issue was found by a static analysis tool I am developing.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64034In the Linux kernel, the following vulnerability has been resolved:
net: mana: Fix TOCTOU double-fetch of hwc_msg_id from DMA buffer
In mana_hwc_rx_event_handler(), resp->response.hwc_msg_id is read from
DMA-coherent memory and bounds-checked, then mana_hwc_handle_resp()
re-reads the same field from the same DMA buffer for test_bit() and
pointer arithmetic.
DMA-coherent memory is mapped uncacheable on x86 and is shared,
unencrypted, in Confidential VMs (SEV-SNP/TDX), so each load goes
directly to host-visible memory. A H/W can modify the value
between the check and the use, bypassing the bounds validation.
Fix this by reading hwc_msg_id exactly once using READ_ONCE() into a
stack-local variable in mana_hwc_rx_event_handler(), and passing the
validated value as a parameter to mana_hwc_handle_resp().Analyse NVD en cours Critique CVSS 9.3 CVE-2026-64035In the Linux kernel, the following vulnerability has been resolved:
igc: set tx buffer type for SMD frames
Sashiko pointed out that igc_fpe_init_smd_frame() initializes
igc_tx_buffer fields for an SMD skb, but does not set the buffer type:
https://sashiko.dev/#/patchset/20260415025226.114115-1-kohei%40enjuk.jp
Since igc_tx_buffer entries are reused, a stale XDP or XSK type can
remain and make TX completion use the wrong cleanup path.
Set the buffer type to IGC_TX_BUFFER_TYPE_SKB.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64036In the Linux kernel, the following vulnerability has been resolved:
cgroup/rstat: validate cpu before css_rstat_cpu() access
css_rstat_updated() is exposed as a BPF kfunc and accepts a
caller-provided cpu argument. The function uses cpu for per-cpu rstat
lookups without checking whether it refers to a valid possible CPU.
A BPF iter/cgroup program with CAP_BPF and CAP_PERFMON can pass an
invalid cpu value. On an unfixed UBSCAN_BOUNDS test kernel, cpu ==
0x7fffffff triggers:
UBSAN: array-index-out-of-bounds in kernel/cgroup/rstat.c:31:9
index 2147483647 is out of range for type 'long unsigned int [64]'
Call Trace:
css_rstat_updated
bpf_iter_run_prog
cgroup_iter_seq_show
bpf_seq_read
Add cpu validation to the BPF-facing css_rstat_updated() kfunc and
move the common implementation to __css_rstat_updated() for in-kernel
callers.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64037In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mld: fix TSO segmentation explosion when AMSDU is disabled
When the TLC notification disables AMSDU for a TID, the MLD driver sets
max_tid_amsdu_len to the sentinel value 1. The TSO segmentation path in
iwl_mld_tx_tso_segment() checks for zero but not for this sentinel,
allowing it to reach the num_subframes calculation:
num_subframes = (max_tid_amsdu_len + pad) / (subf_len + pad)
= (1 + 2) / (1534 + 2) = 0
This zero propagates to iwl_tx_tso_segment() which sets:
gso_size = num_subframes * mss = 0
Calling skb_gso_segment() with gso_size=0 creates over 32000 tiny
segments from a single GSO skb. This floods the TX ring with ~1024
micro-frames (the rest are purged), creating a massive burst of TX
completion events that can lead to memory corruption and a subsequent
use-after-free in TCP's retransmit queue (refcount underflow in
tcp_shifted_skb, NULL deref in tcp_rack_detect_loss).
The MVM driver is immune because it checks mvmsta->amsdu_enabled before
reaching the num_subframes calculation. The MLD driver has no equivalent
bitmap check and relies solely on max_tid_amsdu_len, which does not
catch the sentinel value.
Fix this by detecting the sentinel value (max_tid_amsdu_len == 1) at the
existing check and falling back to non-AMSDU TSO segmentation. Also add
a WARN_ON_ONCE guard after the num_subframes division as defense-in-depth
to catch any future code paths that produce zero through a different
mechanism.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64039In the Linux kernel, the following vulnerability has been resolved:
drm/msm/snapshot: fix dumping of the unaligned regions
The snapshotting code internally aligns data segment to 16 bytes. This
works fine for DPU code (where most of the regions are aligned), but
fails for snapshotting of the DSI data (because DSI data region is
shifted by 4 bytes). Fix the code by removing length alignment and by
accurately printing last registers in the region. While reworking the
code also fix the 16x memory overallocation in
msm_disp_state_dump_regs().
Patchwork: https://patchwork.freedesktop.org/patch/725449/Analyse NVD en cours Élevée CVSS 7.7 CVE-2026-64041In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: fs210x: fix possible buffer overflow
In fs210x_effect_scene_info(), a string was copied like this:
strscpy(DST, SRC, strlen(SRC) + 1);
A buffer overflow would happen if strlen(SRC) >= sizeof(DST).
Actually, strscpy() must be used this way:
strscpy(DST, SRC, sizeof(DST));
strscpy(DST, SRC); // defaults to sizeof(DST)Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64042In the Linux kernel, the following vulnerability has been resolved:
vfio/pci: Check BAR resources before exporting a DMABUF
A DMABUF exports access to BAR resources and, although they are
requested at startup time, we need to ensure they really were reserved
before exporting. Otherwise, it's possible to access unreserved
resources through the export.
Add a check to the DMABUF-creation path.Analyse NVD en cours Élevée CVSS 8.8 CVE-2026-64044In the Linux kernel, the following vulnerability has been resolved:
ovpn: respect peer refcount in CMD_NEW_PEER error path
ovpn_nl_peer_new_doit()'s error path calls ovpn_peer_release() directly
rather than ovpn_peer_put(), bypassing the kref. The accompanying
comment ("peer was not yet hashed, thus it is not used in any context")
holds for UDP but not for TCP.
For UDP, the ovpn_socket union uses the .ovpn arm and never points back
at a peer; UDP encap_recv looks up peers via the not-yet-populated
hashtables, so the new peer is unreachable until ovpn_peer_add()
publishes it.
For TCP, ovpn_socket_new() sets ovpn_sock->peer and
ovpn_tcp_socket_attach() publishes ovpn_sock via rcu_assign_sk_user_data().
From that moment until ovpn_socket_release() detaches in the error path,
the TCP fd is fully wired: userspace recvmsg / sendmsg / close / poll
on the fd, as well as the strparser-driven ovpn_tcp_rcv() path, can
reach the peer through sk_user_data -> ovpn_sock->peer and bump its
refcount via ovpn_peer_hold().
ovpn_tcp_socket_wait_finish() (called inside ovpn_socket_release())
drains strparser and the tx work, but does not synchronize with
userspace syscall callers that already hold a peer reference. If
ovpn_nl_peer_modify() or ovpn_peer_add() returns an error while such
a caller is in flight - notably an ovpn_tcp_recvmsg() blocked in
__skb_recv_datagram() on peer->tcp.user_queue - the direct
ovpn_peer_release() destroys the peer while the caller still holds
the reference, and the eventual ovpn_peer_put() from that caller
operates on freed memory.
Replace the direct destructor call with ovpn_peer_put() so the kref
correctly defers destruction until the last reference is dropped.
In the common case where no concurrent user is present, behaviour is
unchanged: the kref hits zero immediately and ovpn_peer_release_kref()
runs the same destructor.
With this conversion ovpn_peer_release() has no callers outside peer.c
- ovpn_peer_release_kref() in the same translation unit is the only
remaining user - so make it static and drop its declaration from
peer.h.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64045In the Linux kernel, the following vulnerability has been resolved:
ovpn: tcp - use cached peer pointer in ovpn_tcp_close()
ovpn_tcp_close() loads the ovpn_socket via rcu_dereference_sk_user_data()
under rcu_read_lock(), takes a reference on sock->peer, caches the peer
pointer in a local, and drops the read lock. It then passes sock->peer
(rather than the cached local) to ovpn_peer_del(), re-dereferencing the
ovpn_socket after the RCU read section has ended.
Unlike ovpn_tcp_sendmsg(), which uses the same "load under RCU, use
after unlock" pattern but is protected by lock_sock() held across the
function, ovpn_tcp_close() runs without the socket lock: inet_release()
invokes sk_prot->close() without taking lock_sock first.
ovpn_socket_release() can therefore complete its kref_put -> detach ->
synchronize_rcu -> kfree(sock) sequence concurrently, in the window
after ovpn_tcp_close() drops rcu_read_lock() but before it dereferences
sock->peer. The synchronize_rcu() in ovpn_socket_release() protects
readers that use the dereferenced pointer inside the RCU read section,
not those that escape the pointer to a local and use it afterwards.
A reproducer follows the pattern of commit 94560267d6c4 ("ovpn: tcp -
don't deref NULL sk_socket member after tcp_close()"): trigger a peer
removal (keepalive expiration or netlink OVPN_CMD_DEL_PEER) at the same
moment userspace closes the TCP fd. That commit fixed the detach-side
of the same race window; this one fixes the close-side at a different
victim.
Tighten the entry block to read sock->peer exactly once into the cached
peer local, and route all subsequent uses (the hold check, the
ovpn_peer_del() call, and the prot->close() invocation) through that
local. sock->peer is only ever written once in ovpn_socket_new() under
lock_sock(), before rcu_assign_sk_user_data() publishes the ovpn_socket,
and is never reassigned afterwards - but the previous multi-read pattern
made that invariant implicit rather than explicit. The same multi-read
shape exists in ovpn_tcp_recvmsg(), ovpn_tcp_sendmsg(),
ovpn_tcp_data_ready() and ovpn_tcp_write_space(); those will be cleaned
up via a dedicated helper in a follow-up net-next series.Analyse NVD en cours Élevée CVSS 8.4 CVE-2026-64046In the Linux kernel, the following vulnerability has been resolved:
net: tls: prevent chain-after-chain in plain text SG
Sashiko points out that if end = 0 (start != 0) the current
code will create a chain link to content type right after
the wrap link:
This would create a chain where the wrap link points directly
to another chain link. The scatterlist API sg_next iterator
does not recursively resolve consecutive chain links.
meaning this is illegal input to crypto.
The wrapping link is unnecessary if end = 0. end is the entry after
the last one used so end = 0 means there's nothing pushed after
the wrap:
end start i
v v v
[ ]...[ ][ d ][ d ][ d ][ d ][rsv for wrap]
Skip the wrapping in this case.
TLS 1.3 can use the "wrapping slot" for it's chaining if end = 0.
This avoids the chain-after-chain.
Move the wrap chaining before marking END and chaining off content
type, that feels like more logical ordering to me, but should not
matter from functional perspective.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64047In the Linux kernel, the following vulnerability has been resolved:
net: tls: fix off-by-one in sg_chain entry count for wrapped sk_msg ring
When an sk_msg scatterlist ring wraps (sg.end < sg.start),
tls_push_record() chains the tail portion of the ring to the head
using sg_chain(). An extra entry in the sg array is reserved for
this:
struct sk_msg_sg {
[...]
/* The extra two elements:
* 1) used for chaining the front and sections when the list becomes
* partitioned (e.g. end < start). The crypto APIs require the
* chaining;
* 2) to chain tailer SG entries after the message.
*/
struct scatterlist data[MAX_MSG_FRAGS + 2];
The current code uses MAX_SKB_FRAGS + 1 as the ring size:
sg_chain(&msg_pl->sg.data[msg_pl->sg.start],
MAX_SKB_FRAGS - msg_pl->sg.start + 1,
msg_pl->sg.data);
This places the chain pointer at
sg_chain(data[start], (MAX_SKB_FRAGS - msg_start + 1) .. =
&data[start] + (MAX_SKB_FRAGS - msg_start + 1) - 1 =
data[start + (MAX_SKB_FRAGS - start + 1) - 1] =
data[MAX_SKB_FRAGS]
instead of the true last entry. This is likely due to a "race" of
the commit under Fixes landing close to
commit 031097d9e079 ("bpf: sk_msg, zap ingress queue on psock down")
Convert to ARRAY_SIZE and drop the data[start] / - start (as suggested
by Sabrina).Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64048In the Linux kernel, the following vulnerability has been resolved:
net/smc: reject CHID-0 ACCEPT that matches an empty ism_dev slot
On the SMC-D client, slot 0 of ini->ism_dev[]/ini->ism_chid[] is
reserved for an SMC-Dv1 device. smc_find_ism_v2_device_clnt()
populates V2 entries starting at index 1, so when no V1 device is
selected slot 0 is left in its kzalloc()'ed state with ism_dev[0] ==
NULL and ism_chid[0] == 0.
smc_v2_determine_accepted_chid() then matches the peer's CHID against
the array starting from index 0 using the CHID alone. A malicious
peer replying to a SMC-Dv2-only proposal with d1.chid == 0 matches
the empty slot, ini->ism_selected becomes 0, and the subsequent
ism_dev[0]->lgr_lock dereference in smc_conn_create() faults at
offsetof(struct smcd_dev, lgr_lock) == 0x68:
BUG: KASAN: null-ptr-deref in _raw_spin_lock_bh+0x79/0xe0
Write of size 4 at addr 0000000000000068 by task exploit/144
Call Trace:
_raw_spin_lock_bh
smc_conn_create (net/smc/smc_core.c:1997)
__smc_connect (net/smc/af_smc.c:1447)
smc_connect (net/smc/af_smc.c:1720)
__sys_connect
__x64_sys_connect
do_syscall_64
Require ism_dev[i] to be non-NULL before accepting a CHID match.Analyse NVD en cours Élevée CVSS 7.5 CVE-2026-64050In the Linux kernel, the following vulnerability has been resolved:
drm/msm/dpu: don't mix devm and drmm functions
Mixing devm and drmm functions will result in a use-after-free on msm
driver teardown if userspace keeps a reference on the drm device:
The WB connector data will be destroyed because of the use of
devm_kzalloc()), while the usersoace still can try interacting with the
WB connector (which uses drmm_ functions).
Change dpu_writeback_init() to use drmm_.
Patchwork: https://patchwork.freedesktop.org/patch/722656/Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64051In the Linux kernel, the following vulnerability has been resolved:
accel/qaic: Add overflow check to remap_pfn_range during mmap
The call to remap_pfn_range in qaic_gem_object_mmap is susceptible to
(re)mapping beyond the VMA if the BO is too large. This can cause use
after free issues when munmap() unmaps only the VMA region and not the
additional mappings. To prevent this, check the remaining size of the
VMA before remapping and truncate the remapped length if sg->length is
too large.
[jhugo: fix braces from checkpatch --strict]Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64053In the Linux kernel, the following vulnerability has been resolved:
block: don't overwrite bip_vcnt in bio_integrity_copy_user()
bio_integrity_add_page() already sets bip_vcnt to 1 for the bounce
segment. Overwriting it with nr_vecs breaks bip_vcnt <= bip_max_vcnt
on WRITE (bip_max_vcnt is 1), so the gap-merge checks in block/blk.h
read past the bip_vec[] flex array. On READ the read is in bounds
but lands on a saved user bvec instead of the bounce.
The line was added for split propagation, but bio_integrity_clone()
doesn't copy bip_vcnt and BIP_CLONE_FLAGS excludes BIP_COPY_USER.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64055In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: cortina: Carry over frag counter
The gmac_rx() NAPI poll function assembles packets in an
SKB from a ring buffer.
If the ring buffer gets completely emptied during a poll cycle,
we exit gmac_rx(), but the packet is not yet completely
assembled in the SKB, yet the fragment counter frag_nr is
reset to zero on the next invocation.
Solve this by making the RX fragment counter a part of the
port struct, and carry it over between invocations.
Reset the fragment counter only right after calling
napi_gro_frags(), on error (after calling napi_free_frags())
or if stopping the port.
Reset it in some place where not strictly necessary just to
emphasize what is going on.
This was found by Sashiko during normal patch review.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64056In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: cortina: Make RX SKB per-port
The SKB used to assemble packets from fragments in gmac_rx()
is static local, but the Gemini has two ethernet ports, meaning
there can be races between the ports on a bad day if a device
is using both.
Make the RX SKB a per-port variable and carry it over between
invocations in the port struct instead.
Zero the pointer once we call napi_gro_frags(), on error (after
calling napi_free_frags()) or if the port is stopped.
Zero it in some place where not strictly necessary just to
emphasize what is going on.
This was found by Sashiko during normal patch review.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64057In the Linux kernel, the following vulnerability has been resolved:
afs: Fix the locking used by afs_get_link()
The afs filesystem in the kernel doesn't do locking correctly for symbolic
links. There are a number of problems:
(1) It doesn't do any locking around afs_read_single() to prevent races
between multiple ->get_link() calls, thereby allowing the possibility
of leaks.
(2) It doesn't use RCU barriering when accessing the buffer pointers
during RCU pathwalk.
(3) It can race with another thread updating the contents of the symlink
if a third party updated it on the server.
Fix this by the following means:
(0) Move symlink handling into its own file as this makes it more
complicated.
(1) Take the validate_lock around afs_read_single() to prevent races
between multiple ->get_link() calls.
(2) Keep a separate copy of the symlink contents with an rcu_head. This
is always going to be a lot smaller than a page, so it can be
kmalloc'd and save quite a bit of memory. It also needs a refcount
for non-RCU pathwalk.
(3) Split the symlink read and write-to-cache routines in afs from those
for directories.
(4) Discard the I/O buffer as soon as the write-to-cache completes as this
is a full page (plus a folio_queue).
(5) If there's no cache, discard the I/O buffer immediately after reading
and copying if there is no cache.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64058In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix netfs_read_folio() to wait on writeback
Fix netfs_read_folio() to wait for an ongoing writeback to complete so that
it can trust the dirty flag and whatever is attached to folio->private
(folio->private may get cleaned up by the collector before it clears the
writeback flag).Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64061In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix early put of sink folio in netfs_read_gaps()
Fix netfs_read_gaps() to release the sink page it uses after waiting for
the request to complete. The way the sink page is used is that an
ITER_BVEC-class iterator is created that has the gaps from the target folio
at either end, but has the sink page tiled over the middle so that a single
read op can fill in both gaps.
The bug was found by KASAN detecting a UAF on the generic/075 xfstest in
the cifsd kernel thread that handles reception of data from the TCP socket:
BUG: KASAN: use-after-free in _copy_to_iter+0x48a/0xa20
Write of size 885 at addr ffff888107f92000 by task cifsd/1285
CPU: 2 UID: 0 PID: 1285 Comm: cifsd Not tainted 7.0.0 #6 PREEMPT(lazy)
Call Trace:
dump_stack_lvl+0x5d/0x80
print_report+0x17f/0x4f1
kasan_report+0x100/0x1e0
kasan_check_range+0x10f/0x1e0
__asan_memcpy+0x3c/0x60
_copy_to_iter+0x48a/0xa20
__skb_datagram_iter+0x2c9/0x430
skb_copy_datagram_iter+0x6e/0x160
tcp_recvmsg_locked+0xce0/0x1130
tcp_recvmsg+0xeb/0x300
inet_recvmsg+0xcf/0x3a0
sock_recvmsg+0xea/0x100
cifs_readv_from_socket+0x3a6/0x4d0 [cifs]
cifs_read_iter_from_socket+0xdd/0x130 [cifs]
cifs_readv_receive+0xaad/0xb10 [cifs]
cifs_demultiplex_thread+0x1148/0x1740 [cifs]
kthread+0x1cf/0x210Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64066In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix netfs_read_to_pagecache() to pause on subreq failure
Fix netfs_read_to_pagecache() so that it pauses the generation of new
subrequests if an already-issued subrequest fails.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64067In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix missing barriers when accessing stream->subrequests locklessly
The list of subrequests attached to stream->subrequests is accessed without
locks by netfs_collect_read_results() and netfs_collect_write_results(),
and then they access subreq->flags without taking a barrier after getting
the subreq pointer from the list. Relatedly, the functions that build the
list don't use any sort of write barrier when constructing the list to make
sure that the NETFS_SREQ_IN_PROGRESS flag is perceived to be set first if
no lock is taken.
Fix this by:
(1) Add a new list_add_tail_release() function that uses a release barrier
to set the pointer to the new member of the list.
(2) Add a new list_first_entry_or_null_acquire() function that uses an
acquire barrier to read the pointer to the first member in a list (or
return NULL).
(3) Use list_add_tail_release() when adding a subreq to ->subrequests.
(4) Use list_first_entry_or_null_acquire() when initially accessing the
front of the list (when an item is removed, the pointer to the new
front iterm is obtained under the same lock).Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64068In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix missing locking around retry adding new subreqs
Fix netfs_retry_read_subrequests() and netfs_retry_write_stream() to take
the appropriate lock when adding extra subrequests into
stream->subrequests.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64069In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix cancellation of a DIO and single read subrequests
When the preparation of a new subrequest for a read fails, if the
subrequest has already been added to the stream->subrequests list, it can't
simply be put and abandoned as the collector may see it. Also, if it
hasn't been queued yet, it has two outstanding refs that both need to be
put. Both DIO read and single-read dispatch fail at this; further, both
differ in the order they do things to the way buffered read works.
Fix cancellation of both DIO-read and single-read subrequests that failed
preparation by the following steps:
(1) Harmonise all three reads (buffered, dio, single) to queue the subreq
before prepping it.
(2) Make all three call netfs_queue_read() to do the queuing.
(3) Set NETFS_RREQ_ALL_QUEUED independently of the queuing as we don't
know the length of the subreq at this point.
(4) In all cases, set the error and NETFS_SREQ_FAILED flag on the subreq
and then call netfs_read_subreq_terminated() to deal with it. This
will pass responsibility off to the collector for dealing with it.Analyse NVD en cours Critique CVSS 9.8 CVE-2026-64073In the Linux kernel, the following vulnerability has been resolved:
irq_work: Fix use-after-free in irq_work_single() on PREEMPT_RT
On PREEMPT_RT, non-HARD irq_work runs in per-CPU kthreads via
run_irq_workd(), so irq_work_sync() uses rcuwait() to wait for BUSY==0.
After irq_work_single() clears BUSY via atomic_cmpxchg(), it still
dereferences @work for irq_work_is_hard() and rcuwait_wake_up().
An irq_work_sync() caller on another CPU that enters after BUSY is cleared
can observe BUSY==0 immediately, return, and free the work before those
accesses complete — causing a use-after-free.
Fix this by wrapping run_irq_workd() in guard(rcu)() so that the entire
irq_work_single() execution is within an RCU read-side critical
section. Then add synchronize_rcu() in irq_work_sync() after
rcuwait_wait_event() to ensure the caller waits for the RCU grace period
before returning, preventing premature frees.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64074In the Linux kernel, the following vulnerability has been resolved:
fs/statmount: fix slab out-of-bounds write in statmount_mnt_idmap
statmount_mnt_idmap() writes one mapping with seq_printf() and then
manually advances seq->count to include the NUL separator.
If seq_printf() overflows, seq_set_overflow() sets seq->count to
seq->size. The manual seq->count++ changes this to seq->size + 1.
seq_has_overflowed() then no longer detects the overflow. The corrupted
count returns to statmount_string(), which later executes:
seq->buf[seq->count++] = '\0';
This causes a 1-byte NULL out-of-bounds write on the dynamically
allocated seq buffer.
Fix this by checking for overflow immediately after seq_printf().Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64076In the Linux kernel, the following vulnerability has been resolved:
netfilter: bridge: eb_tables: close module init race
sashiko reports for unrelated patch:
Does the core ebtables initialization in ebtables.c suffer from a similar race?
Once nf_register_sockopt() completes, the sockopts are exposed globally.
sockopt has to be registered last, just like in ip/ip6/arptables.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64077In the Linux kernel, the following vulnerability has been resolved:
netfilter: ebtables: move to two-stage removal scheme
Like previous patches for x_tables, follow same pattern in ebtables.
We can't reuse xt helpers: ebt_table struct layout is incompatible.
table->ops assignment is now done while still holding the ebt mutex
to make sure we never expose partially-filled table struct.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64078In the Linux kernel, the following vulnerability has been resolved:
netfilter: x_tables: add and use xtables_unregister_table_exit
Previous change added xtables_unregister_table_pre_exit to detach the
table from the packetpath and to unlink it from the active table list.
In case of rmmod, userspace that is doing set/getsockopt for this table
will not be able to re-instantiate the table:
1. The larval table has been removed already
2. existing instantiated table is no longer on the xt pernet table list.
This adds the second stage helper:
unlink the table from the dying list, free the hook ops (if any) and do
the audit notification. It replaces xt_unregister_table().Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64080In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_ffa: Snapshot notifier callbacks under lock
Both notification handlers currently look up a notifier callback under
notify_lock, drop the lock, and then dereference the returned
notifier entry. A concurrent unregister can delete and free that
entry in the gap, leaving the handler to dereference stale memory.
Copy the callback pointer and callback data while notify_lock is
still held and invoke the callback only after the lock is dropped.
This keeps the existing callback execution model while removing the
use-after-free window in both the framework and non-framework
notification paths.Analyse NVD en cours Critique CVSS 9.3 CVE-2026-64081In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_ffa: Validate framework notification message layout
Framework notifications carry an indirect message in the shared RX
buffer. Validate the reported offset and size before using them, reject
zero-length payloads, and ensure that any non-header payload starts at
the UUID field rather than in the middle of the message header.
Use the validated offset and size values for both kmemdup() and the UUID
parsing path so malformed firmware data cannot drive an out-of-bounds
read or an oversized allocation.Analyse NVD en cours Élevée CVSS 8.4 CVE-2026-64082In the Linux kernel, the following vulnerability has been resolved:
riscv: Fix register corruption from uninitialized cregs on error
compat_riscv_gpr_set() calls cregs_to_regs() unconditionally, even when
user_regset_copyin() fails. Since cregs is an uninitialized stack
variable, a copyin failure causes uninitialized stack data to be written
into the target task's pt_regs, corrupting its register state and
potentially leaking kernel stack contents.
compat_restore_sigcontext() has the same issue: it calls cregs_to_regs()
even when __copy_from_user() fails, leading to the same corruption of
the signal-returning task's register state on error.
Only call cregs_to_regs() when the user copy succeeds.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64084In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pmbus/adm1266) cap PDIO scan in get_multiple at ADM1266_PDIO_NR
adm1266_gpio_get_multiple() iterates the PDIO portion of the
caller-supplied mask using
for_each_set_bit_from(gpio_nr, mask,
ADM1266_GPIO_NR + ADM1266_PDIO_STATUS) {
...
}
where ADM1266_PDIO_STATUS is the PMBus command code (0xE9, i.e. 233),
not the number of PDIO pins. The intended upper bound is
ADM1266_GPIO_NR + ADM1266_PDIO_NR = 25.
gpiolib hands in a mask sized for gc.ngpio (= 25 bits on this chip),
so the iteration walks find_next_bit() up to 242, reading up to 217
extra bits (a handful of unsigned-long words: four on 64-bit, seven
on 32-bit) of whatever lives past the end of the mask in the
caller's stack. Any incidental set bit in that range then drives a
set_bit(gpio_nr, bits) call that writes past the end of the
caller-supplied bits array too -- both out-of-bounds.
Substitute ADM1266_PDIO_NR for the constant so the scan stops at the
last real PDIO bit.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64086In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pmbus/adm1266) include PEC byte in pmbus_block_xfer read buffer
adm1266_pmbus_block_xfer() sets up the read transaction with
.buf = data->read_buf,
.len = ADM1266_PMBUS_BLOCK_MAX + 2,
but read_buf in struct adm1266_data is declared as
u8 read_buf[ADM1266_PMBUS_BLOCK_MAX + 1];
For a max-length block response (length byte = 255 + up to 1 PEC
byte), the i2c controller is told to write 257 bytes into a 256-byte
buffer, putting one byte past the end of read_buf. The same response
also makes the subsequent PEC compare
if (crc != msgs[1].buf[msgs[1].buf[0] + 1])
read a byte beyond the array.
Bump the read_buf declaration to ADM1266_PMBUS_BLOCK_MAX + 2 so the
buffer can hold the length byte, up to 255 payload bytes, and the PEC
byte the i2c_msg length already accounts for.Analyse NVD en cours Élevée CVSS 7.8 CVE-2026-64088In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: fix negative tt_buff_len
batadv_orig_node::tt_buff_len was declared as s16, but the field is never
intended to hold a negative value. When a value greater than 32767 is
assigned, it wraps to a negative signed integer.
In batadv_send_other_tt_response(), tt_buff_len is temporarily widened to
s32. The incorrectly negative s16 value propagates into the s32, causing
batadv_tt_prepare_tvlv_global_data() to allocate a full sized buffer but
populates only a small portion of it with the collected changeset. All
remaining bits are kept uninitialized.
Using an u16 avoids this type confusion and ensures that no (negative) sign
extension is performed in batadv_send_other_tt_response().Analyse NVD en cours Élevée CVSS 8.8 CVE-2026-64089In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: fix negative last_changeset_len
batadv_piv_tt::last_changeset_len len was declared as s16, but the field is
never intended to hold a negative value. When a value greater than 32767 is
assigned, it wraps to a negative signed integer.
In batadv_send_my_tt_response(), last_changeset_len is temporarily widened
to s32. The incorrectly negative s16 value propagates into the s32, causing
batadv_tt_prepare_tvlv_local_data() to allocate a full sized buffer but
populates only a small portion of it with the collected changeset. All
remaining bits are kept uninitialized.
Using an u16 avoids this type confusion and ensures that no (negative) sign
extension is performed in batadv_send_my_tt_response().Analyse NVD en cours Critique CVSS 9.8 1901–2000 / 5155 CVE