Linux
- 150
- vulnerabilities tracked
- 2
- under active exploitation
- 22
- critical
- 27 August 2026
- latest publication
cve
Vulnerability watch
idvulnerabilityseveritypublished
CVE-2026-53362In the Linux kernel, the following vulnerability has been resolved:
ipv6: account for fraggap on the paged allocation path
In __ip6_append_data(), when the paged-allocation branch is taken
(MSG_MORE / NETIF_F_SG / large fraglen), alloclen and pagedlen are
computed as
alloclen = fragheaderlen + transhdrlen;
pagedlen = datalen - transhdrlen;
datalen already includes fraggap (datalen = length + fraggap). When
fraggap is non-zero, this is not the first skb and transhdrlen is zero.
The fraggap bytes carried over from the previous skb are copied just past
the fragment headers in the new skb's linear area. The linear area is
therefore undersized by fraggap bytes while pagedlen is overstated by the
same amount, and the copy writes past skb->end into the trailing
skb_shared_info.
An unprivileged user can trigger this via a UDPv6 socket using
MSG_MORE together with MSG_SPLICE_PAGES.
The bad accounting was introduced by commit 773ba4fe9104 ("ipv6:
avoid partial copy for zc"). Before commit ce650a166335 ("udp6: Fix
__ip6_append_data()'s handling of MSG_SPLICE_PAGES"), the negative
copy value caused -EINVAL to be returned. That later commit allowed
MSG_SPLICE_PAGES to proceed in this case, making the corruption
triggerable.
The non-paged branch sets alloclen to fraglen, which already accounts
for fraggap because datalen does. Bring the paged branch in line by
adding fraggap to alloclen and subtracting it from pagedlen.
After this adjustment, copy no longer collapses to -fraggap on the
paged path, so remove the stale comment describing that old arithmetic.
Since a negative copy is no longer expected for a valid MSG_SPLICE_PAGES
case, remove the MSG_SPLICE_PAGES exception from the negative copy check.Linux Kernel Critical CVSS 7.8 CVE-2022-0995Linux Kernel Out-of-Bounds Write VulnerabilityLinux Kernel Critical CVE-2026-64257In the Linux kernel, the following vulnerability has been resolved:
smb: client: reject overlapping data areas in SMB2 responses
Commit 53b7c271f06b ("smb: client: restrict implied bcc[0] exemption to
responses without data area") restricted the implied bcc[0] length
exception to responses without a data area. However, the overlap
handling in __smb2_calc_size() clears data_length, which can make an
invalid response appear to have no data area and so qualify for the
exception.
Track data area overlap separately and reject such responses before
applying the length compatibility exceptions.Linux Linux Kernel Critical CVSS 9.1 CVE-2026-64259In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: make a fuse_req on SQE commit only findable after memcpy
Bad userspace might try to trick us and send commit SQEs request
unique / commit-id of requests that are not even send to
fuse-server (io_uring_cmd_done() not called) yet.
fuse_uring_commit_fetch() ends the fuse request when the ring entry
has a wrong state, but that could have caused a use-after-free
with the memcpy operations in fuse_uring_send_in_task().
In order to avoid such races the call of fuse_uring_add_to_pq()
is moved after the copy operations and just before completing
the io-uring request - malicious userspace cannot find the request
anymore until all prepration work in fuse-client/kernel is completed.
This also moves fuse_uring_add_to_pq() a bit up in the code to
avoid a forward declaration. Also not with a preparation commit,
to make it easier to back port to older kernels.Linux Linux Kernel High CVSS 7.8 CVE-2026-64260In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: Avoid queue->stopped races and set/read that value under lock
There are several readers of queue->stopped that check the value
under lock, but fuse_uring_commit_fetch() did not and actually
the value was not set under the lock in fuse_uring_abort_end_requests()
either. Especially in fuse_uring_commit_fetch it is important
to check under a lock, because due to races 'struct fuse_req'
might be freed with fuse_request_end, but another thread/cpu
might already do teardown work.Linux Linux Kernel High CVSS 7.8 CVE-2026-64261In the Linux kernel, the following vulnerability has been resolved:
fuse-uring: Avoid use-after-free in fuse_uring_async_stop_queues
fuse_uring_async_stop_queues() might run when the last reference
on ring->queue_refs was already dropped.
In order to avoid an early destruction a reference on struct fuse_conn
is now taken before starting fuse_uring_async_stop_queues() and that
reference is only released when that delayed work queue terminates.Linux Linux Kernel High CVSS 7.8 CVE-2026-64265In the Linux kernel, the following vulnerability has been resolved:
fuse: clear intr_entry in fuse_resend and fuse_remove_pending_req
When fuse_resend() moves a request from fpq->processing back to
fiq->pending, it sets FR_PENDING and clears FR_SENT but does not
remove the requests intr_entry from fiq->interrupts. If the
request had FR_INTERRUPTED set from a prior signal, intr_entry
remains dangling on fiq->interrupts. When the requesting task
then receives a fatal signal, fuse_remove_pending_req() sees
FR_PENDING=1, removes the request from fiq->pending and frees it
via the refcount path, also without cleaning intr_entry. The
stale intr_entry causes use-after-free when fuse_read_interrupt()
iterates fiq->interrupts:
- list_del_init(&req->intr_entry) -> UAF write on freed slab
- req->in.h.unique -> UAF read, data leaked to userspace
Remove intr_entry from fiq->interrupts in fuse_resend() for
interrupted requests before they are placed back on fiq->pending.
Add a WARN_ON if the intr_entry is not empty on request destruction.Linux Linux Kernel High CVSS 7.8 CVE-2026-64266In the Linux kernel, the following vulnerability has been resolved:
fuse: re-lock request before returning from fuse_ref_folio()
fuse_ref_folio() unlocks the request but does not re-lock it before
returning. fuse_chan_abort() can end the request and the async end
callback (eg fuse_writepage_free()) can free the args while the
subsequent copy chain logic after fuse_ref_folio() accesses them,
leading to use-after-free issues.
Fix this by locking the request in fuse_ref_folio() before returning.Linux Linux Kernel High CVSS 7.8 CVE-2026-64268In the Linux kernel, the following vulnerability has been resolved:
RDMA/siw: bound Read Response placement to the RREAD length
In drivers/infiniband/sw/siw/siw_qp_rx.c, siw_proc_rresp() places each
inbound Read Response DDP segment at sge->laddr + wqe->processed and then
accumulates wqe->processed, but it never checks the running total against
the sink buffer length on continuation segments. siw_check_sge() resolves
and validates the sink memory only on the first fragment (the if (!*mem)
branch), and siw_rresp_check_ntoh() compares the cumulative length against
wqe->bytes only on the final segment (the !frx->more_ddp_segs guard).
A connected siw peer that answers an outstanding RREAD with Read Response
segments that keep the DDP Last flag clear, carrying more total payload
than the RREAD requested, drives wqe->processed past the validated sink
buffer; the next siw_rx_data() call writes out of bounds at
sge->laddr + wqe->processed. siw runs iWARP over ordinary routable TCP,
so the peer is the remote end of an established RDMA connection and needs
no local privilege.
Bound every segment before placement, exactly as siw_proc_send() and
siw_proc_write() already do for their tagged and untagged paths, and
terminate the connection with a base-or-bounds DDP error when the
Read Response would overrun the sink buffer.
This is the second receive-path length fix for this file. A separate
change rejects an MPA FPDU length that underflows the per-fragment
remainder in the header decode; that guard does not cover this case,
because here each individual segment length is self-consistent and only
the accumulated placement offset overruns the buffer.Linux Linux Kernel Critical CVSS 9.8 CVE-2026-64269In the Linux kernel, the following vulnerability has been resolved:
RDMA/rtrs-srv: Bound RDMA-Write length to chunk size in rdma_write_sg
When the server answers an RTRS READ, rdma_write_sg() builds the source
scatter/gather entry for the IB_WR_RDMA_WRITE that returns data to the
peer. Its length is taken directly from the wire descriptor:
plist->length = le32_to_cpu(id->rd_msg->desc[0].len);
rd_msg points into the chunk buffer that the remote peer filled via
RDMA-WRITE-WITH-IMM (rtrs_srv_rdma_done() -> process_io_req() ->
process_read()), so desc[0].len is attacker-controlled and, before this
change, was only rejected when zero. The source address is the fixed
chunk start (dma_addr[msg_id]) and the source lkey is the PD-wide
local_dma_lkey, which is not tied to the chunk's MR mapping, so the verbs
layer does not constrain the transfer length to max_chunk_size. msg_id
and off are bounded against queue_depth and max_chunk_size in
rtrs_srv_rdma_done(), but desc[0].len is a separate field that was not
checked against the chunk size.
A peer that advertises desc[0].len larger than max_chunk_size can make
the posted RDMA write read past the chunk's mapped region. The resulting
behaviour depends on the IOMMU configuration: with no IOMMU or in
passthrough mode the read may extend into memory adjacent to the chunk
and be returned to the peer, which can disclose host memory; with a
translating IOMMU the out-of-range access is expected to fault and abort
the connection. In either case the transfer exceeds what the protocol
permits and is driven by a remote peer.
Reject a descriptor length above max_chunk_size, mirroring the existing
off >= max_chunk_size bound in rtrs_srv_rdma_done(). Legitimate clients
do not exceed it: the client sets desc[0].len to its MR length, which is
capped at the negotiated max_io_size (max_chunk_size - MAX_HDR_SIZE).Linux Linux Kernel Critical CVSS 9.1 CVE-2026-64270In the Linux kernel, the following vulnerability has been resolved:
Input: mms114 - reject an oversized device packet size
mms114_interrupt() reads a packet of touch data from the device into a
fixed-size on-stack buffer
struct mms114_touch touch[MMS114_MAX_TOUCH];
which holds MMS114_MAX_TOUCH (10) events of MMS114_EVENT_SIZE (8) bytes,
i.e. 80 bytes. The length of the I2C read into it is taken verbatim from
the device:
packet_size = mms114_read_reg(data, MMS114_PACKET_SIZE);
if (packet_size <= 0)
goto out;
...
error = __mms114_read_reg(data, MMS114_INFORMATION, packet_size,
(u8 *)touch);
packet_size is a single device register byte (0x0F) and the only check
is the lower bound packet_size <= 0; it is never bounded against the
size of touch[]. A malfunctioning, malicious or counterfeit controller
(or an attacker tampering with the I2C bus) can report a packet_size of
up to 255, so __mms114_read_reg() writes up to 175 bytes past the end of
touch[] on the IRQ-thread stack: a stack out-of-bounds write that can
overwrite the stack canary, saved registers and the return address.
A well-formed device never reports more than the buffer holds, so reject
an oversized packet and drop the report, consistent with the handler's
other error paths, rather than reading past the buffer.Linux Linux Kernel High CVSS 7.8 CVE-2026-64271In the Linux kernel, the following vulnerability has been resolved:
Input: touchwin - reset the packet index on every complete packet
tw_interrupt() accumulates each non-zero serial byte into a fixed
three-byte buffer with a running index that is only reset once a full
packet has been received *and* the device's two Y bytes agree:
tw->data[tw->idx++] = data;
if (tw->idx == TW_LENGTH && tw->data[1] == tw->data[2]) {
...
tw->idx = 0;
}
The reset is gated on tw->data[1] == tw->data[2], a value the device
controls. A malicious, malfunctioning or counterfeit Touchwindow
peripheral can stream non-zero bytes whose 2nd and 3rd bytes differ: the
index reaches TW_LENGTH without the equality holding, is never reset, and
keeps growing, so tw->data[tw->idx++] walks off the end of the three-byte
array and the rest of the heap-allocated struct tw, one attacker-chosen
byte at a time -- an unbounded, device-driven heap out-of-bounds write.
Reset the index on every completed packet and report an event only when
the two Y bytes match, like the other serio touchscreen drivers do.Linux Linux Kernel High CVSS 7.8 CVE-2026-64272In the Linux kernel, the following vulnerability has been resolved:
Input: mms114 - fix touch indexing for MMS134S and MMS136
The MMS134S and MMS136 touch controllers have an event size of 6 bytes
rather than 8 bytes. When __mms114_read_reg() reads the touch data
packet from the device into the touch buffer, the events are packed
tightly at 6-byte intervals. However, the driver iterates through the
events using standard C array indexing (touch[index]), where each
element is sizeof(struct mms114_touch) (8 bytes) apart. As a result, any
touch events beyond the first one are read from incorrect offsets and
parsed improperly.
Fix this by explicitly calculating the byte offset for each touch event
based on the device's specific event size.Linux Linux Kernel High CVSS 7.8 CVE-2026-64273In the Linux kernel, the following vulnerability has been resolved:
Input: iforce - bound the device-reported force-feedback effect index
iforce_process_packet() handles a status report (packet id 0x02) by
taking a force-feedback effect index straight from the device wire and
using it to address the per-effect state array:
i = data[1] & 0x7f;
if (data[1] & 0x80) {
if (!test_and_set_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags))
...
} else if (test_and_clear_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags)) {
...
}
The index is masked only with 0x7f, so it ranges 0..127, but
core_effects[] holds only IFORCE_EFFECTS_MAX (32) entries. For an index
of 32..127 the test_and_set_bit()/test_and_clear_bit() is an
out-of-bounds single-bit read-modify-write past the array. core_effects[]
is the second-to-last member of struct iforce, so the write lands in the
trailing members and beyond the embedding kzalloc()'d iforce_serio /
iforce_usb object.
data[1] is unvalidated device payload on both transports (the USB
interrupt endpoint and serio), and the status path is not gated on force
feedback being present, so a malicious or counterfeit device can set or
clear a bit at an attacker-chosen offset past the object.
Reject an out-of-range index instead of indexing with it. Bound against
the array dimension IFORCE_EFFECTS_MAX rather than dev->ff->max_effects so
the check guarantees memory safety regardless of how many effects the
device registered. A legitimate "effect started/stopped" status always
carries an index below IFORCE_EFFECTS_MAX, so well-formed devices are
unaffected; the neighbouring mark_core_as_ready() loop is already bounded
and is left untouched.Linux Linux Kernel High CVSS 7.8 CVE-2026-64274In the Linux kernel, the following vulnerability has been resolved:
Input: goodix - clamp the device-reported contact count
goodix_ts_read_input_report() copies the number of touch points reported
by the device into an on-stack buffer
u8 point_data[2 + GOODIX_MAX_CONTACT_SIZE * GOODIX_MAX_CONTACTS];
which is sized for at most GOODIX_MAX_CONTACTS (10) contacts. The only
runtime check bounds the per-interrupt count against ts->max_touch_num,
but that value is taken verbatim from a 4-bit field of the device
configuration block and is never clamped:
ts->max_touch_num = ts->config[MAX_CONTACTS_LOC] & 0x0f;
The nibble can be 0..15, so a malfunctioning, malicious or counterfeit
controller (or an attacker tampering with the I2C bus) can advertise up
to 15 contacts. goodix_ts_read_input_report() then accepts a touch_num
of up to 15 and the second goodix_i2c_read() writes
ts->contact_size * (touch_num - 1) bytes past the one-contact header into
point_data - up to 30 bytes (45 with the 9-byte report format) beyond the
92-byte buffer: a stack out-of-bounds write.
Clamp max_touch_num to GOODIX_MAX_CONTACTS, the number of contacts
point_data[] is sized for, when reading it from the configuration.Linux Linux Kernel High CVSS 7.8 CVE-2026-64276In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - bound the F30 keymap to the GPIO/LED count
rmi_f30_map_gpios() allocates gpioled_key_map with
min(gpioled_count, TRACKSTICK_RANGE_END) == at most 6 entries, but
rmi_f30_attention() iterates the full f30->gpioled_count (device query
register, range 0..31) and dereferences gpioled_key_map[i], and
input->keycodemax is set to the full gpioled_count while input->keycode
points at the 6-entry allocation.
A device that reports gpioled_count > 6 with GPIO support enabled
therefore causes an out-of-bounds read on the attention interrupt and
out-of-bounds read/write through the EVIOCGKEYCODE/EVIOCSKEYCODE ioctls,
which bound the index only against keycodemax. This is the same defect
as the F3A handler, which was copied from F30.
Size the keymap for the full gpioled_count; the mapping loop still
assigns only the first min(gpioled_count, TRACKSTICK_RANGE_END) entries.Linux Linux Kernel High CVSS 7.8 CVE-2026-64277In the Linux kernel, the following vulnerability has been resolved:
Input: synaptics-rmi4 - bound the F3A keymap to the GPIO count
rmi_f3a_initialize() takes the GPIO count from the device query register
(f3a->gpio_count = buf & RMI_F3A_GPIO_COUNT, range 0..127).
rmi_f3a_map_gpios() then allocates gpio_key_map with
min(gpio_count, TRACKSTICK_RANGE_END) == at most 6 entries, but
rmi_f3a_attention() iterates the full gpio_count and dereferences
gpio_key_map[i], and input->keycodemax is set to the full gpio_count
while input->keycode points at the 6-entry allocation.
A device that reports gpio_count > 6 therefore causes an out-of-bounds
read of gpio_key_map[] on every attention interrupt, and out-of-bounds
accesses through the input core's default keymap ioctls: EVIOCGKEYCODE
reads past the buffer (leaking adjacent slab memory to user space) and
EVIOCSKEYCODE writes a caller-controlled value past it, for any process
able to open the evdev node, since input_default_getkeycode() and
input_default_setkeycode() only bound the index against keycodemax.
Size the keymap for the full gpio_count. The mapping loop is unchanged:
it still assigns only the first min(gpio_count, TRACKSTICK_RANGE_END)
entries; the remaining slots stay KEY_RESERVED (devm_kcalloc zero-fills)
and are skipped when reporting.Linux Linux Kernel High CVSS 7.8 CVE-2026-64279In the Linux kernel, the following vulnerability has been resolved:
i2c: core: fix adapter deregistration race
Adapters can be looked up by their id using i2c_get_adapter() which
takes a reference to the embedded struct device.
Remove the adapter from the IDR before tearing it down during
deregistration (and on registration failure) to make sure its resources
are not accessed after having been freed (e.g. the device name).Linux Linux Kernel High CVSS 7.8 CVE-2026-64280In the Linux kernel, the following vulnerability has been resolved:
fpga: dfl-afu: validate DMA mapping length in afu_dma_map_region()
afu_ioctl_dma_map() accepts a 64-bit length from userspace via
DFL_FPGA_PORT_DMA_MAP ioctl without an upper bound check. The value
is passed to afu_dma_pin_pages() where npages is derived as
length >> PAGE_SHIFT and passed to pin_user_pages_fast() which takes
int nr_pages, causing implicit truncation if length is very large.
Validate map.length at the ioctl entry point before calling
afu_dma_map_region(), rejecting values whose page count exceeds
INT_MAX.Linux Linux Kernel High CVSS 8.8 CVE-2026-64281In the Linux kernel, the following vulnerability has been resolved:
svcrdma: wake sq waiters when the transport closes
Threads parked in svc_rdma_sq_wait() on sc_sq_ticket_wait or
sc_send_wait can hang indefinitely in TASK_UNINTERRUPTIBLE state
across transport teardown, pinning svc_xprt references and
blocking svc_rdma_free().
The close path sets XPT_CLOSE before invoking xpo_detach and both
wait_event predicates include an XPT_CLOSE term, but the
predicates are re-evaluated only on wakeup. sc_sq_ticket_wait has
no completion-driven wake path; it is advanced solely by the
chained ticket handoff inside svc_rdma_sq_wait() itself. Without
an explicit wake at close, parked threads never observe
XPT_CLOSE, hold their svc_xprt_get reference forever, and
svc_rdma_free() blocks on xpt_ref dropping to zero.
Two close entry points reach this transport. Local teardown runs
svc_rdma_detach() from svc_handle_xprt() -> svc_delete_xprt() ->
xpo_detach() on a worker thread. A remote disconnect arrives at
svc_rdma_cma_handler(), which calls svc_xprt_deferred_close():
that sets XPT_CLOSE and enqueues the transport but does not
access either RDMA waitqueue, so a worker already parked in
svc_rdma_sq_wait() never re-evaluates its predicate. With every
worker parked on this transport, no thread is available to run
the local teardown either, and the wake site there is
unreachable.
Introduce svc_rdma_xprt_deferred_close(), a thin svcrdma wrapper
that calls svc_xprt_deferred_close() and then wakes both
sc_sq_ticket_wait and sc_send_wait. Convert the svcrdma producers
that called svc_xprt_deferred_close() directly:
svc_rdma_cma_handler(), qp_event_handler(),
svc_rdma_post_send_err(), svc_rdma_wc_send(), the sendto drop
path, the rw completion error paths, and the recvfrom flush and
read-list error paths.
Wake both waitqueues from svc_rdma_detach() as well. The
synchronous svc_xprt_close() path (backchannel ENOTCONN, device
removal via svc_rdma_xprt_done) reaches detach without flowing
through svc_xprt_deferred_close() and therefore does not invoke
the new helper.
[ cel: add svc_rdma_xprt_deferred_close() to complete the fix ]Linux Linux Kernel High CVSS 7.5 CVE-2026-64283In the Linux kernel, the following vulnerability has been resolved:
KVM: guest_memfd: Treat memslot binding offset+size as unsigned values
When binding a memslot to a guest_memfd file, treat the offset and size as
unsigned values to fix a bug where the sum of the two can result in a false
negative when checking for overflow against the size of the file. Passing
unsigned values also avoids relying on somewhat obscure checks in other
flows for safety, and tracks the offset and size as they are intended to be
tracked, as unsigned values.
On 64-bit kernels, the number of pages a memslot contains and thus the size
(and offset) of its guest_memfd binding are unsigned 64-bit values. Taking
the offset+size as an loff_t instead of a uoff_t inadvertently converts
the unsigned value to a signed value if the offset and/or size is massive.
Locally storing the offset and size as signed values is benign in and of
itself (though even that is *extremely* difficult to discern), but
operating on their sum is not.
For the offset, KVM explicitly checks against a negative value, which might
seem like a bug as KVM could incorrectly reject a legitimate binding, but
that's not actually the case as KVM_CREATE_GUEST_MEMFD takes a signed value
for its size, i.e. a would-be-negative offset is also greater than the
maximum possible size of any guest_memfd file.
Regarding the size, while KVM lacks an explicit check for a negative value,
i.e. seemingly has a flawed overflow check, KVM restricts the number of
pages in a single memslot to the largest positive signed 32-bit value:
if (id < KVM_USER_MEM_SLOTS &&
(mem->memory_size >> PAGE_SHIFT) > KVM_MEM_MAX_NR_PAGES)
return -EINVAL;
and so that maximum "size" will ever be is 0x7fffffff000.
The sum of the two is, however, problematic. While the size is restricted
by KVM's memslot logic, the offset is not, i.e. the offset is completely
unchecked until the "offset + size > i_size_read(inode)" check. If the
offset is the (nearly) largest possible _positive_ value, then adding size
to the offset can result in a signed, negative 64-bit value. When compared
against the size of the file (guaranteed to be positive), the negative sum
is always smaller, and KVM incorrectly allows the absurd offset.
Opportunistically add missing includes in kvm_mm.h (instead of relying on
its parents).Linux Linux Kernel High CVSS 7 CVE-2026-64284In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Ensure vendor's exit handler runs before fastpath userspace exits
Move the handling of fastpath userspace exits into vendor code to ensure
KVM runs vendor specific operations that need to run before userspace gains
control of the vCPU. E.g. for VMX (and soon to be for SVM as well), KVM
needs to flush the PML buffer prior to exiting to userspace, otherwise any
memory written by the final KVM_RUN might never be flagged as dirty.
Note, waiting to snapshot CR0 and CR3 until svm_handle_exit() is flawed in
general, as that risks consuming stale state in a fastpath handler. That
will be addressed in a future change.Linux Linux Kernel High CVSS 7.1 CVE-2026-64286In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Clear __hyp_running_vcpu when flushing the pKVM hyp vCPU
flush_hyp_vcpu() copies the host vCPU context into the hyp's private
vCPU on every run. ctxt_to_vcpu() expects a guest context to have a
NULL __hyp_running_vcpu, which is only ever set on the host context, so
that it resolves the vCPU via container_of(). While this is generally
the case, flush_hyp_vcpu() copies the context verbatim and does not
enforce this, so a value provided by the host is dereferenced at EL2
(host -> EL2).
Fix by clearing __hyp_running_vcpu after the copy.Linux Linux Kernel High CVSS 8.2 CVE-2026-64287In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Bound used_lrs when flushing the pKVM hyp vCPU
flush_hyp_vcpu() copies the host vGIC state into the hyp's private vCPU
on every run. The vGIC list register save and restore use used_lrs as
their loop bound and expect it to stay within the number of implemented
list registers. While this is generally the case, flush_hyp_vcpu()
copies vgic_v3 verbatim and does not enforce this, so a value provided
by the host is used at EL2 to index vgic_lr[] and access ICH_LR<n>_EL2
(host -> EL2).
Fix by clamping used_lrs to the number of implemented list registers
after the copy, as the trusted path already does in
vgic_flush_lr_state(). The number of implemented list registers is
constant after init, so it is replicated once from
kvm_vgic_global_state.nr_lr into hyp_gicv3_nr_lr rather than read on
every entry.Linux Linux Kernel High CVSS 8.2 CVE-2026-64293In the Linux kernel, the following vulnerability has been resolved:
iommufd: Use sizeof(*hdr) instead of sizeof(hdr) in veventq read
The bound-check in iommufd_veventq_fops_read() for the normal vEVENT
path uses sizeof(hdr) where the surrounding code uses sizeof(*hdr):
if (!vevent_for_lost_events_header(cur) &&
sizeof(hdr) + cur->data_len > count - done) {
hdr is declared as struct iommufd_vevent_header *, so sizeof(hdr)
evaluates to the size of the pointer. Surrounding code uses
sizeof(*hdr) consistently:
if (done >= count || sizeof(*hdr) > count - done) {
...
if (copy_to_user(buf + done, hdr, sizeof(*hdr))) {
...
done += sizeof(*hdr);
struct iommufd_vevent_header is currently 8 bytes (two __u32 fields,
flags and sequence), so on 64-bit (sizeof(void *) == 8) the two
expressions happen to be equal and the check works as intended.
On 32-bit (sizeof(void *) == 4) the check under-counts the header by
4 bytes: a vEVENT whose data_len causes 8 + cur->data_len to exceed
count - done while 4 + cur->data_len does not will pass the check,
then the loop will copy_to_user 8 bytes of header followed by data_len
bytes of payload, writing past the user-supplied buffer.
It is also a latent bug for any future expansion of struct
iommufd_vevent_header beyond sizeof(void *) on 64-bit; the check
should not depend on the type happening to match the host pointer
width.
Use sizeof(*hdr) to match the rest of the function and the actual
amount that will be copied.Linux Linux Kernel High CVSS 7.8 CVE-2026-64296In the Linux kernel, the following vulnerability has been resolved:
exfat: bound uniname advance in exfat_find_dir_entry()
In exfat_find_dir_entry(), each TYPE_EXTEND (file name) entry advances the
output pointer by a fixed amount while the loop guard only tracks the
accumulated name length:
if (++order == 2)
uniname = p_uniname->name;
else
uniname += EXFAT_FILE_NAME_LEN;
len = exfat_extract_uni_name(ep, entry_uniname);
name_len += len;
unichar = *(uniname+len);
*(uniname+len) = 0x0;
uniname grows by EXFAT_FILE_NAME_LEN (15) per name entry, but name_len
grows only by the actual extracted length, which is shorter when a name
fragment contains an early NUL. The only guard is
`name_len >= MAX_NAME_LENGTH`, so a crafted directory with many short
name fragments lets uniname run far past the
p_uniname->name[MAX_NAME_LENGTH + 3] buffer while name_len stays small,
causing an out-of-bounds read and write at *(uniname+len).
The sibling extractor exfat_get_uniname_from_ext_entry() already stops
on a short fragment (the lockstep `len != EXFAT_FILE_NAME_LEN` guard
added in commit d42334578eba ("exfat: check if filename entries exceeds
max filename length")); exfat_find_dir_entry() never got the
equivalent. Track the per-entry write offset as a count and reject a
fragment once the offset, or the offset plus the extracted length, would
exceed MAX_NAME_LENGTH, before forming the output pointer.Linux Linux Kernel High CVSS 7.8 CVE-2026-64298In the Linux kernel, the following vulnerability has been resolved:
NFSv4: include MAY_WRITE in open permission mask for O_TRUNC
POSIX requires write permission to truncate a file, so an open() that
specifies O_TRUNC must be authorized for write access regardless of the
O_ACCMODE access mode.
nfs_open_permission_mask() builds the access mask passed to
nfs_may_open(), which is the local authorization gate for OPENs the
client serves itself from a cached write delegation via the
can_open_delegated() path in nfs4_try_open_cached(). The mask is
derived from O_ACCMODE alone, so an open(O_RDONLY | O_TRUNC) against a
file the caller cannot write requests only MAY_READ and passes the
local check. The OPEN is then satisfied locally and the truncation is
issued to the server as a SETATTR(size=0) over the delegation stateid,
which the server accepts under standard write-delegation semantics.
POSIX requires that this open fail with EACCES.
Include MAY_WRITE in the mask whenever O_TRUNC is set so the local
check matches the access the server would have enforced.Linux Linux Kernel High CVSS 7.1 CVE-2026-64208In the Linux kernel, the following vulnerability has been resolved:
crypto/krb5, rxrpc: Fix lack of pre-decrypt/pre-verify length checks
Change the krb5 crypto library to provide facilities to precheck the length
of the message about to be decrypted or verified.
Fix AF_RXRPC to make use of this to validate DATA packets secured with
RxGK.Linux Linux Kernel High CVSS 7.5 CVE-2026-64209In the Linux kernel, the following vulnerability has been resolved:
phy: qcom: qmp-usbc: Fix out-of-bounds array access in dp swing config
swing_tbl and pre_emphasis_tbl are 4x4 arrays (valid indices 0-3), but
the boundary check uses "> 4" instead of ">= 4", allowing index 4 to
cause an out-of-bounds access.Linux Linux Kernel High CVSS 7.1 CVE-2026-64210In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: xsk: Fix unlocked writing to ICOSQ
During napi poll, when the affinity changes and there's still XSK work
to be done, we trigger an ICOSQ interrupt on the new CPU. However, this
triggering on the ICOSQ is done unprotected.
There are 2 such races:
A) mlx5e_trigger_irq() is called while mlx5e_xsk_alloc_rx_mpwqe() is
running from a different CPU due to affinity change. This can happen
because IRQ triggering is done after napi_complete_done(). At this point
the NAPI can be scheduled on a different CPU. Like this:
CPU A (old affinity, NAPI tail) CPU B (new affinity, fresh NAPI)
------------------------------- --------------------------------
napi_complete_done() clears SCHED
mlx5e_cq_arm(...)
napi_schedule_prep() sets SCHED
mlx5e_napi_poll()
mlx5e_xsk_alloc_rx_mpwqe()
mlx5e_icosq_sync_lock() // noop
memcpy 640 B UMR body
advance sq->pc by 10
mlx5e_trigger_irq(&c->icosq)
wqe_info[pi] = {NOP, 1}
mlx5e_post_nop() advances sq->pc
B) mlx5e_trigger_irq() is called on the ICOSQ when
mlx5e_trigger_napi_icosq() is running.
The obvious fix would be to lock the ICOSQ. But ICOSQ has an optimized
locking scheme that doesn't work for this scenario. Kick the async ICOSQ
instead which is always locked.
This issue was noticed in the wild with the following splat:
netdevice: ge-0-0-1: Bad OP in ICOSQ CQE: 0xd
WARNING: drivers/net/ethernet/mellanox/mlx5/core/en_rx.c:826 [...]
[...]
Call Trace:
<IRQ>
mlx5e_napi_poll+0x11d/0x7f0 [mlx5_core]
__napi_poll+0x30/0x200
? skb_defer_free_flush+0x9c/0xc0
net_rx_action+0x2fe/0x3f0
handle_softirqs+0xd8/0x340
__irq_exit_rcu+0xbc/0xe0
common_interrupt+0x85/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x26/0x40
[...]
---[ end trace 0000000000000000 ]---
mlx5_core 0000:08:00.0 ge-0-0-1: Error cqe on cqn 0x548, ci 0x2022, qn 0x8f4,
opcode 0xd, syndrome 0x2, vendor syndrome 0x68
00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000030: 00 00 00 00 01 00 68 02 01 00 08 f4 de 14 59 d2
WQE DUMP: WQ size 16384 WQ cur size 0, WQE index 0x1e14, len: 64
00000000: 00 00 00 01 d9 ed 80 02 00 00 00 01 d9 ed 90 02
00000010: 00 00 00 01 d9 ed a0 02 00 00 00 01 d9 ed b0 02
00000020: 00 00 00 01 d9 ed c0 02 00 00 00 01 d9 ed d0 02
00000030: 00 00 00 01 d9 ed e0 02 00 00 00 01 d9 ed f0 02
mlx5_core 0000:08:00.0 ge-0-0-1: Error cqe on cqn 0x548, ci 0x2023, qn 0x8f4,
opcode 0xd, syndrome 0x5, vendor syndrome 0xf9
00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000030: 00 00 00 00 01 00 f9 05 01 00 08 f4 de 15 cf d2Linux Linux Kernel High CVSS 7.5 CVE-2026-64216In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix potential UAF in netfs_unlock_abandoned_read_pages()
netfs_unlock_abandoned_read_pages(rreq) accesses the index of the folios it
is wanting to unlock and compares that to rreq->no_unlock_folio so that it
doesn't unlock a folio being read for netfs_perform_write() or
netfs_write_begin().
However, given that netfs_unlock_abandoned_read_pages() is called _after_
NETFS_RREQ_IN_PROGRESS is cleared, the one folio that it's not allowed to
dereference is the one specified by ->no_unlock_folio as ownership
immediately reverts to the caller.
Fix this by storing the folio pointer instead and using that rather than
the index. Also fix netfs_unlock_read_folio() where the same applies.Linux Linux Kernel Critical CVSS 9.8 CVE-2026-64217In the Linux kernel, the following vulnerability has been resolved:
netfs: Fix overrun check in netfs_extract_user_iter()
Fix netfs_extract_user_iter() so that if iov_iter_extract_pages() overfills
pages[], then those pages don't get included in the iterator constructed at
the end of the function. If there was an overfill, memory corruption has
already happened.Linux Linux Kernel High CVSS 7.8 CVE-2026-64218In the Linux kernel, the following vulnerability has been resolved:
batman-adv: bla: fix report_work leak on backbone_gw purge
batadv_bla_purge_backbone_gw() removes stale backbone gateway entries,
but fails to properly handle their associated report_work:
- If report_work is running, the purge must wait for it to finish before
freeing the backbone_gw, otherwise the worker may access freed memory
(e.g. bat_priv).
- If report_work is pending, the purge must cancel it and release the
reference held for that pending work item.
The previous implementation called hlist_for_each_entry_safe() inside a
spin_lock_bh() section, but cancel_work_sync() may sleep and therefore
cannot be called from within a spinlock-protected region.
Restructure the loop to handle one entry per spinlock critical section:
acquire the lock, find the next entry to purge, remove it from the hash
list, then release the lock before calling cancel_work_sync() and
dropping the hash_entry reference. Repeat until no more entries require
purging.Linux Linux Kernel High CVSS 7.8 CVE-2026-64219In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Validate payload length and link_index in dc_process_dmub_aux_transfer_async
[Why&How]
dc_process_dmub_aux_transfer_async() copies payload->length bytes into a
16-byte stack buffer (dpaux.data[16]) guarded only by an ASSERT(), which
is a no-op in release builds. If a caller ever passes length > 16 this
results in a stack buffer overflow via memcpy.
Additionally, link_index is used to dereference dc->links[] without
bounds checking against dc->link_count, risking an out-of-bounds access.
Replace the ASSERT with a hard runtime check that returns false when
payload->length exceeds the destination buffer size, and add a bounds
check for link_index before it is used.
(cherry picked from commit ba4caa9fecdf7a38f98c878ad05a8a64148b6881)Linux Linux Kernel High CVSS 7 CVE-2026-64221In the Linux kernel, the following vulnerability has been resolved:
spi: ti-qspi: fix use-after-free after DMA setup failure
The driver falls back to PIO mode if DMA setup fails during probe.
Make sure to clear the DMA channel pointer also if buffer allocation
fails to avoid passing a pointer to the released channel to the DMA
engine (or trying to free the channel a second time on late probe errors
or driver unbind).
This issue was flagged by Sashiko when reviewing a devres allocation
conversion patch.Linux Linux Kernel High CVSS 7.8 CVE-2026-64222In the Linux kernel, the following vulnerability has been resolved:
octeontx2-pf: avoid double free of pool->stack on AQ init failure
otx2_pool_aq_init() frees pool->stack when mailbox sync or retry
allocation fails, but leaves the pointer unchanged. Later,
otx2_sq_aura_pool_init() unwinds the partial setup through
otx2_aura_pool_free(), which frees pool->stack again. The CN20K-specific
cn20k_pool_aq_init() implementation has the same bug in
its corresponding error path.
Set pool->stack to NULL immediately after the local free so the shared
cleanup path does not free the same stack again while cleaning up
partially initialized pool state.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still present in
v7.1-rc3.
Runtime validation was not performed because reproducing this path
requires OcteonTX2/CN20K hardware.Linux Linux Kernel High CVSS 7 CVE-2026-64223In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: consume only present negotiated TTLM maps
ieee80211_tid_to_link_map_size_ok() validates negotiated TTLM elements
against the number of link-map entries indicated by link_map_presence.
ieee80211_parse_neg_ttlm() must consume the same layout.
The parser advanced its cursor for every TID, including TIDs whose
presence bit is clear and therefore have no map bytes in the element.
A sparse map can then make a later present TID read past the validated
element.
The bad bytes land in neg_ttlm->{up,down}link[tid] but are gated by
valid_links before being applied to driver state, so a peer cannot
turn the read into a policy change. Under KUnit + KASAN with an
exact-sized element allocation the OOB read is reported as a
slab-out-of-bounds; whether the same trigger fires under the
production RX path depends on surrounding allocator state.
Advance the cursor only when the current TID has a map present.Linux Linux Kernel High CVSS 8.1 CVE-2026-64224In the Linux kernel, the following vulnerability has been resolved:
octeontx2-pf: fix double free in rvu_rep_rsrc_init()
rvu_rep_rsrc_init() allocates queue memory before calling
otx2_init_hw_resources(). When hardware resource setup fails,
otx2_init_hw_resources() already unwinds the partially initialized
SQ, CQ, and aura state before returning an error. The representor
error path then calls otx2_free_hw_resources() again and can free
the same resources a second time.
Fix this by splitting the cleanup labels so that a failure from
otx2_init_hw_resources() only releases queue memory. Keep the
otx2_free_hw_resources() call for failures that happen after
hardware resource initialization completed successfully.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1-rc3.
Runtime validation was not performed because reproducing this path
requires OcteonTX2 representor hardware.Linux Linux Kernel High CVSS 7.8 CVE-2026-64225In the Linux kernel, the following vulnerability has been resolved:
octeontx2-af: CGX: add bounds check to cgx_speed_mbps index
cgx_speed_mbps has 13 elements but RESP_LINKSTAT_SPEED can yield values
0-15. If it returns a value >= 13, this causes an out-of-bounds array
access. Add a bounds check and default to speed 0 if the index is out of
range.Linux Linux Kernel High CVSS 7.8 CVE-2026-64226In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Avoid UAF in scx_root_enable_workfn() init failure path
In scx_root_enable_workfn(), put_task_struct(p) is called before scx_error()
dereferences p->comm and p->pid. If the iterator's reference is the last
drop, the task is freed synchronously and the deref becomes a UAF.
Move put_task_struct() past scx_error().Linux Linux Kernel High CVSS 7.8 CVE-2026-64232In the Linux kernel, the following vulnerability has been resolved:
block: recompute nr_integrity_segments in blk_insert_cloned_request
blk_insert_cloned_request() already recomputes nr_phys_segments
against the bottom queue, because "the queue settings related to
segment counting may differ from the original queue." The exact same
reasoning applies to integrity segments: a stacked driver's underlying
queue can have tighter virt_boundary_mask, seg_boundary_mask, or
max_segment_size than the top queue, in which case
blk_rq_count_integrity_sg() against the bottom queue produces a
different count than the cached rq->nr_integrity_segments inherited
from the source request by blk_rq_prep_clone().
When the cached count is lower than the bottom queue's actual count,
blk_rq_map_integrity_sg() trips
BUG_ON(segments > rq->nr_integrity_segments);
on dispatch. The same families of stacked setups that motivated the
existing nr_phys_segments recompute -- dm-multipath fanning out to
nvme-rdma in particular -- can produce this.
Mirror the nr_phys_segments handling: when the request carries
integrity, recompute nr_integrity_segments against the bottom queue
and reject the request if it exceeds the bottom queue's
max_integrity_segments. blk_rq_count_integrity_sg() and
queue_max_integrity_segments() are both already available via
<linux/blk-integrity.h>, which blk-mq.c includes.
This closes a latent gap in the stacking contract and brings the
integrity-segment accounting in line with the existing
phys-segment accounting.Linux Linux Kernel Critical CVSS 9.8 CVE-2026-64235In the Linux kernel, the following vulnerability has been resolved:
x86/ftrace: Relocate %rip-relative percpu refs in dynamic trampolines
With CONFIG_CALL_DEPTH_TRACKING enabled on an x86 retbleed-affected platform
(eg: Skylake), with retbleed=stuff, registering a dynamic ftrace trampoline
crashes on the first call into the traced function:
BUG: unable to handle page fault for address: ffff88817ae18880
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 4b53067 P4D 4b53067 PUD 0
Oops: Oops: 0002 [#1] SMP PTI
CPU: 3 UID: 0 PID: 187 Comm: usleep Not tainted 7.0.10 #243 PREEMPT(full)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.17.0-2-2 04/01/2014
Code: 24 78 00 00 00 00 48 89 ea 48 89 54 24 20 48 8b b4 24 b8 00 00 00 48 8b bc 24 b0 00 00 00 48 89 bc 24 80 00 00 00 48 83 ef 05 <65> 48 c1 3d 1f a8 b6 02 05 48 8b 15 f6 00 00 00 4c 89 3c 24 4c 89
Call Trace:
<TASK>
? find_held_lock
? exc_page_fault
? lock_release
? __x64_sys_clock_nanosleep
? lockdep_hardirqs_on_prepare
? trace_hardirqs_on
__x64_sys_clock_nanosleep
do_syscall_64
? exc_page_fault
? call_depth_return_thunk
entry_SYSCALL_64_after_hwframe
...
Kernel panic - not syncing: Fatal exception
This small reproducer allows to easily trigger the crash:
# echo 'p __x64_sys_clock_nanosleep' > /sys/kernel/tracing/kprobe_events
# echo 1 > /sys/kernel/tracing/events/kprobes/p___x64_sys_clock_nanosleep_0/enable
# usleep 1
Monitoring the crash under GDB points to the exact instruction in charge of
incrementing the call depth:
sarq $5, %gs:__x86_call_depth(%rip)
This instruction matches the one inserted by the ftrace_regs_caller from
ftrace_64.S. This emitted code was likely working fine until the introduction
of
59bec00ace28 ("x86/percpu: Introduce %rip-relative addressing to PER_CPU_VAR()"):
it has made the call depth accounting addressing relative to $rip, instead of
being based on an absolute address.
As this code exact location depends on where the trampoline lives in memory,
the corresponding displacement needs to be adjusted at runtime to actually
correctly find the per-cpu __x86_call_depth value, otherwise the targeted
address is wrong, leading to the page fault seen above.
Fix the %rip-relative displacement of the copied CALL_DEPTH_ACCOUNT
instruction (from ftrace_regs_caller) by calling text_poke_apply_relocation(),
as it is done for example by the x86 BPF JIT compiler through
x86_call_depth_emit_accounting(). This corrects both CALL_DEPTH_ACCOUNT slots,
in ftrace_caller and ftrace_regs_caller.
[ bp: Massage. ]Linux Linux Kernel High CVSS 8.1 CVE-2026-64237In the Linux kernel, the following vulnerability has been resolved:
Input: elan_i2c - validate firmware size before use
Ensure that the firmware file is large enough to contain the expected
number of pages and the signature (which resides at the end of the
firmware blob) before accessing them to prevent potential out-of-bounds
reads.Linux Linux Kernel High CVSS 7.1 CVE-2026-64239In the Linux kernel, the following vulnerability has been resolved:
mm/damon/sysfs-schemes: delete tried region in regions_rmdirs()
DAMON sysfs maintains the DAMOS tried region directory objects via a
linked list. When the user requests refresh of the directories, DAMON
sysfs removes all the region directories first, and then generate updated
regions directory on the empty space. The removal function
(damon_sysfs_scheme_regions_rm_dirs()) only puts the kobj objects.
Deletion of the container region object from the linked list is done
inside the kobj release callback function.
If somehow the callback invocation is delayed, the list will contain
regions list that gonna be freed. If the updated region directories
creation is started in this situation, the list can be corrupted and
use-after-free can happen.
Because the kobj objects are managed by only DAMON sysfs, the issue cannot
happen in normal situation. But, such delays can be made on kernels that
built with CONFIG_DEBUG_KOBJECT_RELEASE. On the kernel, the issue can
indeed be reproduced like below.
# damo start --damos_action stat
# cd /sys/kernel/mm/damon/admin/kdamonds/0/
# for i in {1..10}; do echo update_schemes_tried_regions > state; done
# dmesg | grep underflow
[ 89.296152] refcount_t: underflow; use-after-free.
Fix the issue by removing the region object from the list when
decrementing the reference count.
Also update damos_sysfs_populate_region_dir() to add the region object to
the list only after the kobject_init_and_add() is success, so that fail of
kobject_init_and_add() is not leaving the deallocated object on the list.
The issue was discovered [1] by Sashiko.Linux Linux Kernel High CVSS 7.8 CVE-2026-64242In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: net2280: Fix double free in probe error path
usb_initialize_gadget() installs gadget_release() as the release
callback for the embedded gadget device. The struct net2280 instance is
therefore released through gadget_release() when the gadget device's last
reference is dropped.
The probe error path calls net2280_remove(), which tears down the
partially initialized device and drops the gadget reference with
usb_put_gadget(). Calling kfree(dev) afterwards can free the same object
again.
Drop the explicit kfree() and let the gadget device release callback
handle the final free. This issue was found by a static analysis tool
I am developing.Linux Linux Kernel High CVSS 7.8 CVE-2026-64243In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: simple-mux: Fix enum control bounds check
simple_mux_control_put() rejects values greater than e->items, but
enum control values are zero based. For the two-entry mux used by this
driver, valid values are 0 and 1, so value 2 must be rejected as well.
Accepting e->items can store an invalid mux state, pass it to the GPIO
setter, and pass it on to the DAPM mux update path where it is used as
an index into the enum text array.
Use the same >= e->items check used by the ASoC enum helpers.Linux Linux Kernel High CVSS 7.1 CVE-2026-64245In the Linux kernel, the following vulnerability has been resolved:
fbdev: modedb: fix a possible UAF in fb_find_mode()
If mode_option is NULL, it is assigned from mode_option_buf:
if (!mode_option) {
fb_get_options(NULL, &mode_option_buf);
mode_option = mode_option_buf;
}
Later, name is assigned from mode_option:
const char *name = mode_option;
However, mode_option_buf is freed before name is no longer used:
kfree(mode_option_buf);
while name is still accessed by:
if ((name_matches(db[i], name, namelen) ||
Since name aliases mode_option_buf, this may result in a
use-after-free.
Fix this by extending the lifetime of mode_option_buf until the end of the
function by using scope-based resource management for cleanup.Linux Linux Kernel High CVSS 7.8 CVE-2026-64246In the Linux kernel, the following vulnerability has been resolved:
power: reset: linkstation-poweroff: fix use-after-free in the linkstation_poweroff_init()
Move of_node_put(dn) after the of_match_node() call, which still needs
the node pointer. The node reference is correctly released after use.Linux Linux Kernel High CVSS 7.8 CVE-2026-64247In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: hyper-v: Bound the bank index when querying sparse banks
When checking if a VP ID is included in a sparse bank set, explicitly check
that the ID can actually be contained in a sparse bank (the TLFS allows for
a maximum of 64 banks of 64 vCPUs each). When handling a paravirtual TLB
flush for L2, the VP ID is copied verbatim from the enlightened VMCS,
without any bounds check, i.e. isn't guaranteed to be under the limit of
4096.
Failure to check the bounds of the VP ID leads to an out-of-bounds read
when testing the sparse bank, and super strictly speaking could lead to KVM
performing an unnecessary TLB flush for an L2 vCPU.
==================================================================
BUG: KASAN: use-after-free in hv_is_vp_in_sparse_set+0x85/0x100 [kvm]
Read of size 8 at addr ffff88811ba5f598 by task hyperv_evmcs/2802
CPU: 12 UID: 1000 PID: 2802 Comm: hyperv_evmcs Not tainted 7.1.0-rc2 #7 PREEMPT
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
Call Trace:
<TASK>
dump_stack_lvl+0x51/0x60
print_report+0xcb/0x5d0
kasan_report+0xb4/0xe0
kasan_check_range+0x35/0x1b0
hv_is_vp_in_sparse_set+0x85/0x100 [kvm]
kvm_hv_flush_tlb+0xe9e/0x16c0 [kvm]
kvm_hv_hypercall+0xe6b/0x1e60 [kvm]
vmx_handle_exit+0x485/0x1b60 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0x22e3/0x5070 [kvm]
kvm_vcpu_ioctl+0x5d0/0x10c0 [kvm]
__x64_sys_ioctl+0x129/0x1a0
do_syscall_64+0xb9/0xcf0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f0e62d1a9bf
</TASK>
The buggy address belongs to the physical page:
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0xffffffffffffffff pfn:0x11ba5f
flags: 0x4000000000000000(zone=1)
raw: 4000000000000000 0000000000000000 00000000ffffffff 0000000000000000
raw: ffffffffffffffff 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88811ba5f480: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff88811ba5f500: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>ffff88811ba5f580: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
^
ffff88811ba5f600: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff88811ba5f680: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
==================================================================
Disabling lock debugging due to kernel taint
Opportunistically add a compile time assertion to ensure the maximum number
of sparse banks exactly matches the number of possible bits in the passed
in mask.
[sean: add KASAN splat, drop comment, add assert, massage changelog]Linux Linux Kernel High CVSS 8.4 CVE-2026-64249In the Linux kernel, the following vulnerability has been resolved:
fpga: region: fix use-after-free in child_regions_with_firmware()
Move of_node_put(child_region) after the error print to avoid accessing
freed memory when pr_err() references child_region.
[ Yilun: Fix the Fixes tag ]Linux Linux Kernel High CVSS 7.8 CVE-2026-64251In the Linux kernel, the following vulnerability has been resolved:
pwrseq: core: fix use-after-free in pwrseq_debugfs_seq_next()
pwrseq_debugfs_seq_next() declares 'next' with __free(put_device),
which causes put_device() to be called on the returned pointer when
the variable goes out of scope. This results in a use-after-free
since the seq_file framework receives a pointer whose reference has
already been dropped.
Simply removing __free(put_device) would fix the UAF but would leak
the reference acquired by bus_find_next_device(), as stop() only
calls up_read(&pwrseq_sem) and never releases the device reference.
Fix this by making the reference counting consistent across all
seq_file callbacks, matching the standard pattern used by PCI and
SCSI:
- start(): use get_device() so it returns a referenced pointer.
- next(): explicitly put_device(curr) to release the previous
device's reference (no NULL check needed - the seq_file framework
only calls next() while the previous return was non-NULL).
- stop(): put_device(data) to release the last iterated device's
reference, with a NULL guard since stop() may be called with NULL
when start() returned NULL or next() reached end-of-sequence.Linux Linux Kernel High CVSS 7.8 CVE-2026-64255In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mld: validate sta_mask before ffs() in BA session handlers
Three BA session handlers use ffs(ba_data->sta_mask) - 1 to derive a
station ID without checking that sta_mask is non-zero. When sta_mask is
zero, ffs() returns 0 and the subtraction wraps to 0xFFFFFFFF, causing
an out-of-bounds access on fw_id_to_link_sta[].
Add WARN_ON_ONCE(!ba_data->sta_mask) guards before each ffs() call,
consistent with the existing check in iwl_mld_ampdu_rx_start().Linux Linux Kernel High CVSS 8.8 CVE-2026-64600In the Linux kernel, the following vulnerability has been resolved:
xfs: resample the data fork mapping after cycling ILOCK
xfs_reflink_fill_{cow_hole,delalloc} are both presented with an inode,
a data fork mapping, and a cow fork mapping. Unfortunately, these two
helpers cycle the ILOCK to grab a transaction, which means that the
mappings are stale as soon as we reacquire the ILOCK. Currently we
refresh the cow fork mapping by re-calling xfs_find_trim_cow_extent, but
we don't refresh the data fork mapping beforehand, which means that the
xfs_bmap_trim_cow in that function queries the refcount btree about the
wrong physical blocks and returns an inaccurate value in *shared.
If *shared is now false, the directio write proceeds with a stale data
fork mapping. Fix this by querying the data fork mapping if the
sequence counter changes across the ILOCK cycle.Linux Linux Kernel High CVSS 7.8 CVE-2026-64188In the Linux kernel, the following vulnerability has been resolved:
net: qualcomm: rmnet: fix endpoint use-after-free in rmnet_dellink()
rmnet_dellink() removes the endpoint from the hash table with
hlist_del_init_rcu() and then immediately frees it with kfree(). However,
RCU readers on the receive path (rmnet_rx_handler ->
__rmnet_map_ingress_handler) may still hold a reference to the endpoint and
dereference ep->egress_dev after the memory has been freed. The endpoint is
a kmalloc-32 object, and the stale read at offset 8 corresponds to the
egress_dev pointer.
BUG: unable to handle page fault for address: ffffffffde942eef
Oops: 0002 [#1] SMP NOPTI
CPU: 1 UID: 0 PID: 137 Comm: poc_write Not tainted 7.0.0+ #4 PREEMPTLAZY
RIP: 0010:rmnet_vnd_rx_fixup (rmnet_vnd.c:27)
Call Trace:
<TASK>
__rmnet_map_ingress_handler (rmnet_handlers.c:48 rmnet_handlers.c:101)
rmnet_rx_handler (rmnet_handlers.c:129 rmnet_handlers.c:235)
__netif_receive_skb_core.constprop.0 (net/core/dev.c:6096)
__netif_receive_skb_one_core (net/core/dev.c:6208)
netif_receive_skb (net/core/dev.c:6467)
tun_get_user (drivers/net/tun.c:1955)
tun_chr_write_iter (drivers/net/tun.c:2003)
vfs_write (fs/read_write.c:688)
ksys_write (fs/read_write.c:740)
</TASK>
Add an rcu_head field to struct rmnet_endpoint and replace kfree() with
kfree_rcu() so the endpoint memory remains valid through the RCU grace
period. Also remove the rmnet_vnd_dellink() call and inline only the
nr_rmnet_devs decrement, since rmnet_vnd_dellink() would set
ep->egress_dev to NULL during the grace period, creating a data race
with lockless readers.Linux Linux Kernel High CVSS 7.8 CVE-2026-64189In the Linux kernel, the following vulnerability has been resolved:
netfilter: ipset: fix race between dump and ip_set_list resize
The release path of ip_set_dump_do() and ip_set_dump_done() read
inst->ip_set_list via ip_set_ref_netlink(), a plain rcu_dereference_raw()
of the array pointer. These run from netlink_recvmsg() without the nfnl
mutex and without an RCU read-side critical section.
A concurrent ip_set_create() can grow the array: it publishes the new
array, calls synchronize_net() and then kvfree()s the old one. Since the
dump paths read the array outside any RCU reader, synchronize_net() does
not wait for them and the old array can be freed while they still index
into it, causing a use-after-free.
The dumped set itself stays pinned via set->ref_netlink, so only the
array load needs protecting. Take rcu_read_lock() around it, matching
ip_set_get_byname() and __ip_set_put_byindex().
BUG: KASAN: slab-use-after-free in ip_set_dump_do (net/netfilter/ipset/ip_set_core.c:1697)
Read of size 8 at addr ffff88800b5c4018 by task exploit/150
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
ip_set_dump_do (net/netfilter/ipset/ip_set_core.c:1697)
netlink_dump (net/netlink/af_netlink.c:2325)
netlink_recvmsg (net/netlink/af_netlink.c:1976)
sock_recvmsg (net/socket.c:1159)
__sys_recvfrom (net/socket.c:2315)
...
Oops: general protection fault, probably for non-canonical address ... KASAN NOPTI
KASAN: maybe wild-memory-access in range [0x02d6...d0-0x02d6...d7]
RIP: 0010:ip_set_dump_do (net/netfilter/ipset/ip_set_core.c:1698)
Kernel panic - not syncing: Fatal exceptionLinux Linux Kernel High CVSS 7.8 CVE-2026-64191In the Linux kernel, the following vulnerability has been resolved:
i2c: stub: Reject I2C block transfers with invalid length
The I2C_SMBUS_I2C_BLOCK_DATA case in stub_xfer() uses data->block[0]
as the transfer length. The existing check only clamps it to avoid
overrunning the chip->words[256] register array, but does not validate
it against I2C_SMBUS_BLOCK_MAX (32), which is the limit of the union
i2c_smbus_data.block buffer (34 bytes total). The driver is a
development/test tool (CONFIG_I2C_STUB=m, not built by default)
that must be loaded with a chip_addr= parameter.
A local user with access to /dev/i2c-* can issue an I2C_SMBUS ioctl
with I2C_SMBUS_I2C_BLOCK_DATA and data->block[0] > 32, causing
stub_xfer() to read or write past the end of the union
i2c_smbus_data.block buffer:
BUG: KASAN: stack-out-of-bounds in stub_xfer (drivers/i2c/i2c-stub.c:223)
Read of size 1 at addr ffff88800abcfd92 by task exploit/81
Call Trace:
<TASK>
stub_xfer (drivers/i2c/i2c-stub.c:223)
__i2c_smbus_xfer (drivers/i2c/i2c-core-smbus.c:593)
i2c_smbus_xfer (drivers/i2c/i2c-core-smbus.c:536)
i2cdev_ioctl_smbus (drivers/i2c/i2c-dev.c:391)
i2cdev_ioctl (drivers/i2c/i2c-dev.c:478)
__x64_sys_ioctl (fs/ioctl.c:583)
do_syscall_64 (arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
</TASK>
The bug exists because i2c-stub implements .smbus_xfer directly,
bypassing the I2C_SMBUS_BLOCK_MAX validation in
i2c_smbus_xfer_emulated(). The I2C_SMBUS_BLOCK_DATA case in the same
function correctly validates against I2C_SMBUS_BLOCK_MAX, but the
I2C_SMBUS_I2C_BLOCK_DATA case does not.
Fix by rejecting transfers with data->block[0] == 0 or
data->block[0] > I2C_SMBUS_BLOCK_MAX with -EINVAL, consistent with
both the I2C_SMBUS_BLOCK_DATA case in the same function and the
I2C_SMBUS_I2C_BLOCK_DATA validation in i2c_smbus_xfer_emulated().Linux Linux Kernel High CVSS 7.8 CVE-2026-64206In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: cancel pending_rx_work before taking conn->lock
l2cap_conn_del() takes conn->lock and then calls cancel_work_sync() for
pending_rx_work. process_pending_rx() takes the same mutex, so teardown
can deadlock against the worker it is flushing.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the l2cap_conn_ready() -> queue_work(...,
&conn->pending_rx_work) submit path, the l2cap_conn_del() ->
cancel_work_sync(&conn->pending_rx_work) teardown path, and the
process_pending_rx() -> mutex_lock(&conn->lock) worker edge. Lockdep
WARNING: possible circular locking dependency detected
process_pending_rx+0x21/0x2a [vuln_msv]
l2cap_conn_del.constprop.0+0x3f/0x4e [vuln_msv]
*** DEADLOCK ***
Cancel pending_rx_work before taking conn->lock, matching the existing
lock-before-drain ordering used for the two delayed works in the same
teardown path. The pending_rx queue is still purged after the work has
been cancelled and conn->lock has been acquired.Linux Linux Kernel High CVSS 8.8 CVE-2026-53368In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix fsck inconsistency caused by incorrect nat_entry flag usage
f2fs_need_dentry_mark() reads nat_entry flags without mutual exclusion
with the checkpoint path, which can result in an incorrect inode block
marking state. The scenario is as follows:
create & write & fsync 'file A' write checkpoint
- f2fs_do_sync_file // inline inode
- f2fs_write_inode // inode folio is dirty
- f2fs_write_checkpoint
- f2fs_flush_merged_writes
- f2fs_sync_node_pages
- f2fs_fsync_node_pages // no dirty node
- f2fs_need_inode_block_update // return true
- f2fs_fsync_node_pages // inode dirtied
- f2fs_need_dentry_mark //return true
- f2fs_flush_nat_entries
- f2fs_write_checkpoint end
- __write_node_folio // inode with DENT_BIT_SHIFT set
SPO, "fsck --dry-run" find inode has already checkpointed but still
with DENT_BIT_SHIFT set
The state observed by f2fs_need_dentry_mark() can differ from the state
observed in __write_node_folio() after acquiring sbi->node_write. The
root cause is that the semantics of IS_CHECKPOINTED and
HAS_FSYNCED_INODE are only guaranteed after the checkpoint write has
fully completed.
This patch moves set_dentry_mark() into __write_node_folio() and
protects it with the sbi->node_write lock.Linux Linux Kernel High CVSS 7.1 CVE-2026-53369In the Linux kernel, the following vulnerability has been resolved:
udf: reject descriptors with oversized CRC length
udf_read_tagged() skips CRC verification when descCRCLength +
sizeof(struct tag) exceeds the block size. A crafted UDF image can
set descCRCLength to an oversized value to bypass CRC validation
entirely; the descriptor is then accepted based solely on the 8-bit
tag checksum, which is trivially recomputable.
Reject such descriptors instead of silently accepting them. A
legitimate single-block descriptor should never have a CRC length that
exceeds the block.Linux Linux Kernel High CVSS 8.4 CVE-2026-53373In the Linux kernel, the following vulnerability has been resolved:
mm/vma: do not try to unmap a VMA if mmap_prepare() invoked from mmap()
The mmap_prepare hook functionality includes the ability to invoke
mmap_prepare() from the mmap() hook of existing 'stacked' drivers, that is
ones which are capable of calling the mmap hooks of other drivers/file
systems (e.g. overlayfs, shm).
As part of the mmap_prepare action functionality, we deal with errors by
unmapping the VMA should one arise. This works in the usual mmap_prepare
case, as we invoke this action at the last moment, when the VMA is
established in the maple tree.
However, the mmap() hook passes a not-fully-established VMA pointer to the
caller (which is the motivation behind the mmap_prepare() work), which is
detached.
So attempting to unmap a VMA in this state will be problematic, with the
most obvious symptom being a warning in vma_mark_detached(), because the
VMA is already detached.
It's also unncessary - the mmap() handler will clean up the VMA on error.
So to fix this issue, this patch propagates whether or not an mmap action
is being completed via the compatibility layer or directly.
If the former, then we do not attempt VMA cleanup, if the latter, then we
do.
This patch also updates the userland VMA tests to reflect the change.Linux Linux Kernel High CVSS 7.8 CVE-2026-53374In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: zero-initialize GART table on allocation
GART TLB is flushed after unmapping but not after mapping. Since
amdgpu_bo_create_kernel() does not zero-initialize the buffer, when a
single PTE is written the TLB may speculatively load other uninitialized
entries from the same cacheline. Those garbage entries can appear valid,
and a subsequent write to another PTE in the same cacheline may cause the
GPU to use a stale garbage PTE from the TLB.
Fix this by calling memset_io() to zero-initialize the GART table with
gart_pte_flags immediately after allocation.
Using AMDGPU_GEM_CREATE_VRAM_CLEARED, SDMA-based clear will not work
since SDMA needs GART to be initialized to work.
(cherry picked from commit d9af8263b82b6eaa60c5718e0c6631c5037e4b24)Linux Linux Kernel High CVSS 8.8 CVE-2026-53375In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/vce: Prevent partial address patches
In the case that only one of lo/hi is valid, the patching could result
in a bad address written to in FW.Linux Linux Kernel High CVSS 8.8 CVE-2026-53380In the Linux kernel, the following vulnerability has been resolved:
media: rzv2h-ivc: Fix concurrent buffer list access
The list of buffers (`rzv2h_ivc::buffers.queue`) is protected by a
spinlock (`rzv2h_ivc::buffers.lock`). However, in
`rzv2h_ivc_transfer_buffer()`, which runs in a separate workqueue, the
`list_del()` call is executed without holding the spinlock, which makes
it possible for the list to be concurrently modified
Fix that by removing a buffer from the list in the lock protected section.
[assign ivc->buffers.curr in critical section as reported by Barnabas]Linux Linux Kernel High CVSS 7.8 CVE-2026-53381In the Linux kernel, the following vulnerability has been resolved:
virtiofs: fix UAF on submount umount
iput() called from fuse_release_end() can Oops if the super block has
already been destroyed. Normally this is prevented by waiting for
num_waiting to go down to zero before commencing with super block shutdown.
This only works, however, for the last submount instance, as the wait
counter is per connection, not per superblock.
Revert to using synchronous release requests for the auto_submounts case,
which is virtiofs only at this time.Linux Linux Kernel High CVSS 7.8 CVE-2026-53383In the Linux kernel, the following vulnerability has been resolved:
ksmbd: reject non-VALID session in compound request branch
smb2_check_user_session() takes a shortcut for any operation that is not
the first in a COMPOUND request: it reuses work->sess (the session bound by
the first operation) and validates only the SessionId, then returns
"valid". It never re-checks work->sess->state == SMB2_SESSION_VALID, and a
SessionId of 0xFFFFFFFFFFFFFFFF (ULLONG_MAX, the MS-SMB2 related-operation
value) skips even the id comparison. The standalone path
(ksmbd_session_lookup_all() plus the SESSION_SETUP state machine) does
enforce the VALID state; the compound branch bypasses all of it.
A SESSION_SETUP carrying only an NTLM Type-1 (NtLmNegotiate) blob publishes
a fresh SMB2_SESSION_IN_PROGRESS session whose sess->user is still NULL
(->user is assigned later, by ntlm_authenticate()). Used as operation 1 of
a COMPOUND with operation 2 = TREE_CONNECT (related, SessionId=ULLONG_MAX,
\\host\IPC$), the tree-connect then runs on that IN_PROGRESS session and
reaches ksmbd_ipc_tree_connect_request(), which dereferences
user_name(sess->user) with sess->user == NULL (transport_ipc.c:687/701/704)
-> remote NULL-pointer dereference and a kernel Oops that wedges the ksmbd
worker for all clients.
Reject any non-first compound operation that lands on a session which is
not SMB2_SESSION_VALID, mirroring the validity the standalone lookup path
enforces. SESSION_SETUP itself legitimately runs on an IN_PROGRESS session,
but it is never carried as a non-first compound operation, so multi-leg
authentication is unaffected by this check.Linux Linux Kernel High CVSS 7.5 CVE-2026-53384In the Linux kernel, the following vulnerability has been resolved:
serial: 8250_dw: unregister 8250 port if clk_notifier_register() fails
dw8250_probe() registers the 8250 port via serial8250_register_8250_port()
and then, if the device has a clock, registers a clock notifier. If
clk_notifier_register() fails, probe returns the error but leaves the
8250 port registered. The matching serial8250_unregister_port() lives
in dw8250_remove(), which is not called when probe fails, so the port
slot stays occupied until the device is rebound or the system is
rebooted. The devm-allocated driver data is freed while the port still
references it (via the saved private_data and serial_in/serial_out
callbacks), so any access to that port slot before a rebind is a
use-after-free hazard.
Unregister the port on the clk_notifier_register() error path.Linux Linux Kernel Critical CVSS 9.8 CVE-2026-53386In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ti-ads1298: add bounds check to pga_settings index
ads1298_pga_settings has 7 elements but ADS1298_MASK_CH_PGA can yield
values 0-7. If it yields a value >= 7, this causes an out-of-bounds
array access. Add a bounds check and return -EINVAL if the index
is out of range.
Note that the remaining value b111 is reserved so should not be seen
in a correctly functioning system.Linux Linux Kernel High CVSS 7.8 CVE-2026-53387In the Linux kernel, the following vulnerability has been resolved:
iio: light: veml6075: add bounds check to veml6075_it_ms index
veml6075_it_ms has 5 elements but VEML6075_CONF_IT can yield values 0-7.
If it returns a value >= 5, this causes an out-of-bounds array access.
Add a bounds check and return -EINVAL if the index is out of range.
The problem values are reserved so should never be read from the
register. Hence this is hardening against fault device, missprogramming
or bus corruption.Linux Linux Kernel High CVSS 7.1 CVE-2026-53388In the Linux kernel, the following vulnerability has been resolved:
fuse: re-lock request before replacing page cache folio
fuse_try_move_folio() unlocks the request on entry but does not
re-lock it on the success path. This means fuse_chan_abort() can end the
request and free the fuse_io_args (eg fuse_readpages_end()) while the
subsequent copy chain logic after fuse_try_move_folio() accesses the
fuse_io_args, leading to use-after-free issues.
Fix this by calling lock_request() before replace_page_cache_folio().
This ensures the request is locked on the success path which will
prevent the fuse_io_args from being freed while the later copying logic
runs, and also ensures that the ap->folios[i]->mapping is never null
since ap->folios[i] will always point to the newfolio after
replace_page_cache_folio().Linux Linux Kernel High CVSS 7.8 CVE-2026-53389In the Linux kernel, the following vulnerability has been resolved:
net/tcp-ao: fix use-after-free of key in del_async path
In tcp_ao_delete_key(), the del_async path skips the current_key
and rnext_key validity checks present in the synchronous path,
assuming these pointers are always NULL on LISTEN sockets. However,
if a key was added with set_current=1/set_rnext=1 while the socket
was in CLOSE state, current_key and rnext_key will be non-NULL
after listen() transitions the socket to LISTEN.
When such a key is deleted with del_async=1, hlist_del_rcu() and
call_rcu() free the key without clearing the dangling pointers.
After the RCU grace period, getsockopt(TCP_AO_INFO) dereferences
current_key->sndid and rnext_key->rcvid from freed slab memory.
Clear current_key and rnext_key in the del_async path when they
reference the key being deleted.Linux Linux Kernel High CVSS 7.8 CVE-2026-53390In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix out-of-bounds read in smb_check_perm_dacl()
The permission-check ACE walk in smb_check_perm_dacl() validates the ACE
header size and caps sid.num_subauth at SID_MAX_SUB_AUTHORITIES, but it
never checks that ace->size is actually large enough to contain
num_subauth sub-authorities before compare_sids() dereferences them.
CIFS_SID_BASE_SIZE covers the SID header up to but excluding the
sub_auth[] array, and offsetof(struct smb_ace, sid) is the ACE header,
so the existing guards only guarantee the 8-byte SID base, i.e. zero
sub-authorities. compare_sids() then reads ace->sid.sub_auth[i] for
i < min(local_sid->num_subauth, ace->sid.num_subauth). The local
comparison SIDs (sid_everyone, sid_unix_NFS_mode, and the id_to_sid()
result) always have at least one sub-authority, and an attacker controls
the ACE revision and authority bytes (which lie within the in-bounds SID
base), so they can match one of those SIDs and force the sub_auth read.
A crafted ACE with size == 16 and num_subauth >= 1 placed at the tail of
the security descriptor therefore causes a heap out-of-bounds read of up
to SID_MAX_SUB_AUTHORITIES * sizeof(__le32) bytes past the pntsd
allocation. The security descriptor is loaded by ksmbd_vfs_get_sd_xattr()
into a buffer sized exactly to the on-disk data (kzalloc(sd_size) in
ndr_decode_v4_ntacl()), so the read lands past the allocation. The
malformed descriptor can be stored verbatim via SMB2_SET_INFO (the DACL
is not normalised before being written to the security.NTACL xattr) and
the read fires on a subsequent SMB2_CREATE access check, making this
reachable by an authenticated client on a share that uses ACL xattrs.
Add the missing num_subauth-versus-ace_size check, mirroring the
identical guards already present in the sibling parsers parse_dacl() and
smb_inherit_dacl().Linux Linux Kernel High CVSS 8.1 CVE-2026-53391In the Linux kernel, the following vulnerability has been resolved:
NFSv4/pNFS: reject zero-length r_addr in nfs4_decode_mp_ds_addr
nfs4_decode_mp_ds_addr() decodes the r_netid and r_addr opaques of a
netaddr4 from a GETDEVICEINFO multipath-DS body, then immediately
calls strrchr(buf, '.') to locate the port separator. Both decodes
use xdr_stream_decode_string_dup(), and the current code checks only
"nlen < 0" / "rlen < 0" before dereferencing the returned string.
When the on-wire opaque has length zero, xdr_stream_decode_opaque_inline()
returns 0 and xdr_stream_decode_string_dup() falls through to its
"*str = NULL; return ret" tail, leaving buf NULL with a return value
of 0. The "< 0" check does not catch this, and the next line is
strrchr(NULL, '.'), a kernel NULL pointer dereference reachable from
any pNFS-flexfile client mounted against a malicious or compromised
metadata server.
Reject the zero-length cases explicitly so the decoder fails with
-EBADMSG (treated as a malformed GETDEVICEINFO body) instead of
panicking the client.Linux Linux Kernel High CVSS 7.5 CVE-2026-53392In the Linux kernel, the following vulnerability has been resolved:
NFSv4/flexfiles: reject zero filehandle version count
ff_layout_alloc_lseg() decodes the filehandle-version array count
from the flexfiles layout body. The value is used as the count for
kzalloc_objs(), and the current code only rejects NULL.
A zero count yields ZERO_SIZE_PTR, which can be stored in
dss_info->fh_versions even though later flexfiles paths assume that at
least one filehandle version exists.
Reject fh_count == 0 before the allocation, matching the existing zero
version_count validation in the flexfiles GETDEVICEINFO parser.
A QEMU/KASAN run with a malformed flexfiles layout hit:
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
RIP: 0010:ff_layout_encode_ff_layoutupdate.isra.0+0x15f/0x750
ff_layout_encode_layoutreturn+0x683/0x970
nfs4_xdr_enc_layoutreturn+0x278/0x3a0
Kernel panic - not syncing: Fatal exception
The patched kernel rejects the malformed layout without KASAN/oops/panic,
and a valid fh_count=1 regression still opens, reads, and unmounts cleanly.Linux Linux Kernel High CVSS 7.5 CVE-2026-53394In the Linux kernel, the following vulnerability has been resolved:
nfsd: avoid leaking pre-allocated openowner on unconfirmed retry race
When find_or_alloc_open_stateowner() encounters an unconfirmed owner, it
calls release_openowner() and sets oo = NULL. Control then falls through
past the `if (oo)` guard -- which would have freed any pre-allocated
`new` -- and unconditionally executes `new = alloc_stateowner(...)`. If
`new` was already allocated on a prior iteration, the pointer is
silently overwritten and the previous allocation (slab object + owner
name buffer) is leaked.
This requires a race: two NFSv4.0 OPEN threads with the same owner
string, where a concurrent thread inserts a new unconfirmed owner into
the hash between retry iterations. The window is narrow but repeatable
under adversarial conditions.
Fix by adding `goto retry` after `oo = NULL` so the already-allocated
`new` is reused on the next iteration rather than overwritten.Linux Linux Kernel High CVSS 7.5 CVE-2026-53395In the Linux kernel, the following vulnerability has been resolved:
nfsd: fix dead ACL conflict guard in nfsd4_create
nfsd4_create() steals create->cr_dpacl/cr_pacl into the local
nfsd_attrs via the designated initializer, then immediately sets the
source pointers to NULL. The subsequent conflict guard tests the
already-nilled source fields, making it permanently dead code:
if (create->cr_acl) {
if (create->cr_dpacl || create->cr_pacl) /* always false */
When a client encodes both FATTR4_WORD0_ACL and
FATTR4_WORD2_POSIX_{DEFAULT,ACCESS}_ACL in the same CREATE fattr
bitmap, nfsd4_acl_to_attr() overwrites attrs.na_pacl/na_dpacl without
releasing the originals, leaking two posix_acl slab objects per
request. Repeated requests cause unbounded slab exhaustion.
Fix by checking attrs.na_dpacl/na_pacl (the stolen values) instead of
the nilled create->cr_dpacl/cr_pacl, matching the correct pattern
already used in nfsd4_setattr().Linux Linux Kernel High CVSS 7.5 CVE-2026-53396In the Linux kernel, the following vulnerability has been resolved:
nfsd: fix posix_acl leak and ignored error in nfsd4_create_file
nfsd4_create_file() has two bugs in its ACL handling:
The return value of nfsd4_acl_to_attr() is silently discarded. When
the NFSv4-to-POSIX ACL conversion fails (e.g., -EINVAL for
unsupported ACE types), the file is created without any ACL and the
client receives NFS4_OK. This violates RFC 7530/8881 which require
the server to reject unsupported attributes on CREATE.
When start_creating() fails after ACL attributes have been populated
in attrs (either via nfsd4_acl_to_attr or via ownership transfer from
open->op_dpacl/op_pacl), the function jumps to out_write which skips
nfsd_attrs_free(). The posix_acl allocations are leaked. A client
can trigger this repeatedly with OPEN(CREATE), ACL attributes, and an
invalid filename (e.g., longer than NAME_MAX).
Fix both by capturing the nfsd4_acl_to_attr() return value and by
changing the early error paths to jump to out instead of out_write.
Initialize child to ERR_PTR(-EINVAL) so that end_creating() is safe
to call even if start_creating() was never reached.Linux Linux Kernel High CVSS 7.1 CVE-2026-53397In the Linux kernel, the following vulnerability has been resolved:
nfsd: fix posix_acl leak on SETACL decode failure
nfsaclsvc_decode_setaclargs() and nfs3svc_decode_setaclargs() each
call nfs_stream_decode_acl() twice, first for NFS_ACL and then for
NFS_DFACL. Each successful call transfers ownership of a freshly
allocated posix_acl into argp->acl_access or argp->acl_default. If
the first call succeeds but the second fails, the decoder returns
false and argp->acl_access is left dangling.
ACLPROC2_SETACL.pc_release was wired to nfssvc_release_attrstat and
ACLPROC3_SETACL.pc_release was wired to nfs3svc_release_fhandle.
Both only call fh_put() and have no knowledge of the ACL fields on
argp. The posix_acl_release() pairs sat at the out: labels inside
nfsacld_proc_setacl() and nfsd3_proc_setacl(), but svc_process()
skips pc_func when pc_decode returns false, so that cleanup is
unreachable on decode failure:
svc_process_common()
pc_decode() /* decode_setaclargs: false */
/* pc_func skipped */
pc_release() /* fh_put only -- ACLs leaked */
The orphaned posix_acl is leaked for the lifetime of the server.
Fix by adding nfsaclsvc_release_setacl() and nfs3svc_release_setacl(),
which release both argp->acl_access and argp->acl_default in addition
to fh_put(), and wiring them as pc_release for their respective SETACL
procedures. pc_release runs on every path svc_process() takes after
decode, including decode failure, so the posix_acl_release() pairs are
removed from the proc functions' out: labels to keep ownership in one
place. This matches the existing release_getacl() pattern used by
the sibling GETACL procedures.Linux Linux Kernel High CVSS 7.5 CVE-2026-53398In the Linux kernel, the following vulnerability has been resolved:
NFSD: Fix SECINFO_NO_NAME decode error cleanup
nfsd4_decode_secinfo_no_name() currently initializes sin_exp after
decoding sin_style. If the XDR stream is truncated, the decoder returns
nfserr_bad_xdr before sin_exp is initialized.
Since commit 3fdc54646234 ("NFSD: Reduce amount of struct
nfsd4_compoundargs that needs clearing"), the inline iops array is not
cleared between RPC calls. A failed SECINFO_NO_NAME decode can therefore
leave sin_exp holding stale union contents from a previous operation.
The error response path still invokes nfsd4_secinfo_no_name_release(),
which calls exp_put() on a non-NULL sin_exp.
Initialize sin_exp before the first failable decode step, matching
nfsd4_decode_secinfo().Linux Linux Kernel Critical CVSS 9.8 CVE-2026-53399In the Linux kernel, the following vulnerability has been resolved:
nfsd: release layout stid on setlease failure
nfs4_alloc_stid() publishes the new stid into cl->cl_stateids via
idr_alloc_cyclic() under cl_lock before returning to
nfsd4_alloc_layout_stateid(). When nfsd4_layout_setlease() then
fails, the error path frees the layout stateid directly with
kmem_cache_free() without ever calling idr_remove(), leaving the
IDR slot pointing at freed slab memory. Any subsequent IDR walker
(states_show, client teardown) dereferences the dangling pointer.
The correct teardown for an IDR-published stid is nfs4_put_stid(),
which removes the IDR slot under cl_lock, dispatches sc_free
(nfsd4_free_layout_stateid) to release ls->ls_file via
nfsd4_close_layout(), and drops the nfs4_file reference in its
tail.
A second issue blocks that switch: nfsd4_free_layout_stateid()
unconditionally inspects ls->ls_fence_work via
delayed_work_pending() under ls_lock, but
INIT_DELAYED_WORK(&ls->ls_fence_work, ...) currently runs only
after the setlease call. On the setlease-failure path the
destructor would touch an uninitialized delayed_work.
nfsd4_alloc_layout_stateid()
nfs4_alloc_stid() /* idr_alloc_cyclic under cl_lock */
nfsd4_layout_setlease() /* fails */
nfs4_put_stid()
nfsd4_free_layout_stateid()
delayed_work_pending(&ls->ls_fence_work) /* needs INIT */
nfsd4_close_layout() /* nfsd_file_put(ls->ls_file) */
put_nfs4_file()
Fix by hoisting the ls_fenced / ls_fence_delay / INIT_DELAYED_WORK
initialization above the nfsd4_layout_setlease() call, and replace
the manual nfsd_file_put + put_nfs4_file + kmem_cache_free cleanup
with a single nfs4_put_stid(stp).Linux Linux Kernel Critical CVSS 9.8 CVE-2026-53400In the Linux kernel, the following vulnerability has been resolved:
i2c: core: fix adapter registration race
Adapters can be looked up based on their id using i2c_get_adapter()
which takes a reference to the embedded struct device.
Make sure that the adapter (including its struct device) has been
initialised before adding it to the IDR to avoid accessing uninitialised
data which could, for example, lead to NULL-pointer dereferences or
use-after-free.
Note that the i2c-dev chardev, which is registered from a bus notifier,
currently uses i2c_get_adapter() so the adapter needs to be added to the
IDR before registration.Linux Linux Kernel High CVSS 7.8 CVE-2026-53401In the Linux kernel, the following vulnerability has been resolved:
fbdev: omap2: fix use-after-free in omapfb_mmap
omapfb_mmap() has a race condition with OMAPFB_SETUP_PLANE ioctl that
can lead to use-after-free:
The fb_mmap() entry point holds mm_lock but not lock (fb_info->lock),
while ioctl handlers like OMAPFB_SETUP_PLANE hold lock but not mm_lock.
This allows concurrent execution.
In omapfb_mmap():
1. rg = omapfb_get_mem_region(ofbi->region); // Get old region ref
2. start = omapfb_get_region_paddr(ofbi); // Read from NEW region
3. len = fix->smem_len; // Read from NEW region
4. vm_iomap_memory(vma, start, len); // Map NEW region memory
5. atomic_inc(&rg->map_count); // Increment OLD region!
Concurrently, OMAPFB_SETUP_PLANE can:
- Reassign ofbi->region = new_rg
- Update fix->smem_len
- OMAPFB_SETUP_MEM then checks NEW region's map_count (0!) and frees it
This leaves userspace with a mapping to freed physical memory.
The fix is to read all required values (start, len) from the same
region reference (rg) that will have its map_count incremented,
preventing the region from being freed while still mapped.Linux Linux Kernel High CVSS 7.8 CVE-2026-53402In the Linux kernel, the following vulnerability has been resolved:
fbdev: fbcon: fix out-of-bounds read in err_out of fbcon_do_set_font()
When fbcon_do_set_font() fails (e.g., due to a memory allocation failure
inside vc_resize() under heavy memory pressure), it jumps to the `err_out`
label to roll back the console state. However, the current rollback logic
forgets to restore the `hi_font` state, leading to a severe state machine
corruption.
Earlier in the function, `set_vc_hi_font()` might be called to change
`vc->vc_hi_font_mask` and mutate the screen buffer. If `vc_resize()`
subsequently fails, the `err_out` path restores `vc_font.charcount`
but entirely skips rolling back the `vc_hi_font_mask` and the screen
buffer.
This mismatch leaves the terminal in a desynchronized state. Because
`vc_hi_font_mask` remains set, the VT subsystem will still accept
character indices greater than 255 from userspace and write them to the
screen buffer. Subsequent rendering calls (e.g., `fbcon_putcs()`) will
then use these inflated indices to access the reverted, 256-character
font array, leading to a deterministic out-of-bounds read and potential
kernel memory disclosure.
Fix this by adding the missing rollback logic for the `hi_font` mask
and screen buffer in the error path.Linux Linux Kernel High CVSS 7.1 CVE-2026-63793In the Linux kernel, the following vulnerability has been resolved:
ntfs: serialize volume label accesses
Protect vol->volume_label with a mutex and snaphost the label before
copy_to_user. This prevent a use-after-free when FS_IOC_SETFSLABEL
replaces the vol->volume_label and FS_IOC_GETTSLABEL reads it
concurrently.Linux Linux Kernel High CVSS 7.8 CVE-2026-63794In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Fix page overflow in sev_dbg_crypt() for ENCRYPT path
In sev_dbg_crypt(), the per-iteration transfer length is bounded by
the source page offset (PAGE_SIZE - s_off) but not by the destination
page offset (PAGE_SIZE - d_off). When d_off > s_off, the encrypt
path (__sev_dbg_encrypt_user) performs a read-modify-write using a
single-page intermediate buffer (dst_tpage):
1. __sev_dbg_decrypt() expands the size to round_up(len + (d_off & 15), 16)
before issuing the PSP command. If len + (d_off & 15) > PAGE_SIZE,
the PSP writes beyond the end of the 4096-byte dst_tpage allocation.
2. The subsequent memcpy()/copy_from_user() into
page_address(dst_tpage) + (d_off & 15) of 'len' bytes overflows
by up to 15 bytes under the same condition.
Trigger example: s_off = 0, d_off = 1, debug.len = PAGE_SIZE -
the PSP is instructed to write round_up(4097, 16) = 4112 bytes to
a 4096-byte buffer.
Fix by also bounding len by (PAGE_SIZE - d_off), the same check that
sev_send_update_data() already performs for its single-page guest
region.
==================================================================
BUG: KASAN: slab-use-after-free in sev_dbg_crypt+0x993/0xd10 [kvm_amd]
Write of size 4095 at addr ff110062293bb009 by task sev_dbg_test/228214
CPU: 96 UID: 0 PID: 228214 Comm: sev_dbg_test Tainted: G U W 7.0.0-smp--5ce9b0c48211-dbg #156 PREEMPTLAZY
Tainted: [U]=USER, [W]=WARN
Hardware name: Google Astoria/astoria, BIOS 0.20250817.1-0 08/25/2025
Call Trace:
<TASK>
dump_stack_lvl+0x54/0x70
print_report+0xbc/0x260
kasan_report+0xa2/0xd0
kasan_check_range+0x25f/0x2c0
__asan_memcpy+0x40/0x70
sev_dbg_crypt+0x993/0xd10 [kvm_amd]
sev_mem_enc_ioctl+0x33c/0x450 [kvm_amd]
kvm_vm_ioctl+0x65d/0x6d0 [kvm]
__se_sys_ioctl+0xb2/0x100
do_syscall_64+0xe8/0x870
entry_SYSCALL_64_after_hwframe+0x4b/0x53
</TASK>
The buggy address belongs to the physical page:
page: refcount:1 mapcount:0 mapping:0000000000000000 index:0x7fe72b6a0 pfn:0x62293bb
memcg:ff11000112827d82
flags: 0x1400000000000000(node=1|zone=1)
raw: 1400000000000000 0000000000000000 dead000000000122 0000000000000000
raw: 00000007fe72b6a0 0000000000000000 00000001ffffffff ff11000112827d82
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ff110062293bbf00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ff110062293bbf80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ff110062293bc000: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
^
ff110062293bc080: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
ff110062293bc100: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
==================================================================
Disabling lock debugging due to kernel taint
[sean: add sample KASAN splat, Fixes, and stable@]Linux Linux Kernel High CVSS 7.8 CVE-2026-63795In the Linux kernel, the following vulnerability has been resolved:
9p: avoid putting oldfid in p9_client_walk() error path
When p9_client_walk() is called with clone set to false, fid aliases
oldfid. If the walk subsequently fails after the request has been sent,
the error path jumps to clunk_fid, which currently calls p9_fid_put(fid)
unconditionally.
This drops a reference to oldfid even though ownership of oldfid remains
with the caller. If this is the last reference, oldfid can be clunked and
destroyed while the caller still expects it to be valid. A later use or
put of oldfid can then trigger a use-after-free or refcount underflow.
Fix this by only putting fid in the clunk_fid error path when it does not
alias oldfid, matching the existing guard in the error path below.
This can be triggered when a multi-component walk is split into multiple
p9_client_walk() calls and a later non-cloning walk fails. A reproducer
and refcount warning logs are available on request.Linux Linux Kernel Critical CVSS 10 CVE-2026-63796In the Linux kernel, the following vulnerability has been resolved:
ocfs2: reject oversized group bitmap descriptors
ocfs2_validate_gd_parent() only bounds bg_bits against the parent
allocator's chain geometry. A malicious descriptor can still claim a
bg_size/bg_bits pair that exceeds the bitmap bytes that physically fit in
the group descriptor block, so later bitmap scans and bit updates can run
past bg_bitmap.
Add a physical-cap check based on ocfs2_group_bitmap_size() for the parent
allocator type and reject descriptors whose bg_size or bg_bits exceed that
capacity. Keep the existing chain geometry check so both the on-disk
bitmap layout and the allocator metadata must agree before the descriptor
is used.
Validation reproduced this kernel report:
KASAN use-after-free in _find_next_bit+0x7f/0xc0
Read of size 8
Call trace:
dump_stack_lvl+0x66/0xa0 (?:?)
print_report+0xd0/0x630 (?:?)
_find_next_bit+0x7f/0xc0 (?:?)
srso_alias_return_thunk+0x5/0xfbef5 (?:?)
__virt_addr_valid+0x188/0x2f0 (?:?)
kasan_report+0xe4/0x120 (?:?)
ocfs2_find_max_contig_free_bits+0x35/0x70 (fs/ocfs2/suballoc.c:1375)
ocfs2_block_group_set_bits+0x472/0x4b0 (fs/ocfs2/suballoc.c:1457)
ocfs2_cluster_group_search+0x16b/0x440 (fs/ocfs2/suballoc.c:86)
ocfs2_bg_discontig_fix_result+0x1ef/0x230 (fs/ocfs2/suballoc.c:1786)
ocfs2_search_chain+0x8f8/0x10a0 (fs/ocfs2/suballoc.c:1886)
get_page_from_freelist+0x70e/0x2370 (?:?)
lock_release+0xc6/0x290 (?:?)
do_raw_spin_unlock+0x9a/0x100 (?:?)
kasan_unpoison+0x27/0x60 (?:?)
__bfs+0x147/0x240 (?:?)
get_page_from_freelist+0x83d/0x2370 (?:?)
ocfs2_claim_suballoc_bits+0x38c/0xe70 (fs/ocfs2/suballoc.c:96)
sched_domains_numa_masks_clear+0x70/0xd0 (?:?)
check_irq_usage+0xe8/0xb70 (?:?)
__ocfs2_claim_clusters+0x18d/0x4c0 (fs/ocfs2/suballoc.c:2497)
check_path+0x24/0x50 (?:?)
rcu_is_watching+0x20/0x50 (?:?)
check_prev_add+0xfd/0xd00 (?:?)
ocfs2_add_clusters_in_btree+0x17d/0x810 (fs/ocfs2/suballoc.c:?)
__folio_batch_add_and_move+0x1f5/0x3d0 (?:?)
ocfs2_add_inode_data+0xd9/0x120 (fs/ocfs2/suballoc.c:?)
filemap_add_folio+0x105/0x1f0 (?:?)
ocfs2_write_begin_nolock+0x29f7/0x2f80 (fs/ocfs2/suballoc.c:3043)
ocfs2_read_inode_block+0xb5/0x110 (fs/ocfs2/suballoc.c:?)
down_write+0xf5/0x180 (?:?)
ocfs2_write_begin+0x180/0x240 (fs/ocfs2/suballoc.c:?)
__mark_inode_dirty+0x758/0x9a0 (?:?)
inode_to_bdi+0x41/0x90 (?:?)
balance_dirty_pages_ratelimited_flags+0xf8/0x1d0 (?:?)
generic_perform_write+0x252/0x440 (?:?)
mnt_put_write_access_file+0x16/0x70 (?:?)
file_update_time_flags+0xe4/0x200 (?:?)
ocfs2_file_write_iter+0x80a/0x1320 (fs/ocfs2/suballoc.c:?)
lock_acquire+0x184/0x2f0 (?:?)
ksys_write+0xd2/0x170 (?:?)
apparmor_file_permission+0xf5/0x310 (?:?)
read_zero+0x8d/0x140 (?:?)
lock_is_held_type+0x8f/0x100 (?:?)Linux Linux Kernel High CVSS 8.8 CVE-2026-63797In the Linux kernel, the following vulnerability has been resolved:
rpmsg: char: Fix use-after-free on probe error path
rpmsg_chrdev_probe() stores the newly allocated eptdev in the default
endpoint's priv pointer before calling rpmsg_chrdev_eptdev_add(). If
rpmsg_chrdev_eptdev_add() then fails, its error path frees eptdev while
the default endpoint may still dispatch callbacks with the stale priv
pointer.
Avoid publishing eptdev through the default endpoint until
rpmsg_chrdev_eptdev_add() succeeds. Messages received before the priv
pointer is published should be ignored by rpmsg_ept_cb(). Flow-control
updates can hit rpmsg_ept_flow_cb() in the same window, so make both
callbacks return success when priv is NULL.Linux Linux Kernel High CVSS 8.4 CVE-2026-63799In the Linux kernel, the following vulnerability has been resolved:
sched/mmcid: Fix OOB clear_bit when CID is MM_CID_UNSET in fixup path
In mm_cid_fixup_cpus_to_tasks(), when rq->curr has the target mm and
mm_cid.active is set, the CID is checked with cid_in_transit() before
setting the transition bit. In per-CPU mode a newly forked or exec'd
task can be running with mm_cid.cid == MM_CID_UNSET because CIDs are
assigned lazily on schedule-in. With cid_in_transit() the guard passes
for MM_CID_UNSET (no transit bit), converts it to MM_CID_UNSET |
MM_CID_TRANSIT and stores it back; later mm_cid_schedout() feeds this
to clear_bit() with MM_CID_UNSET as the bit number, triggering an
out-of-bounds write.
Symptoms: this is genuine memory corruption, but a bounded out-of-bounds
write, not an arbitrary one. MM_CID_UNSET is the fixed sentinel BIT(31),
so once the bad value reaches mm_cid_schedout() the cid_from_transit_cid()
strip leaves MM_CID_UNSET, which fails the "cid < max_cids" convergence
test and falls into mm_drop_cid() -> clear_bit(MM_CID_UNSET,
mm_cidmask(mm)). The cid bitmap is embedded in the mm_struct slab object
(after cpu_bitmap and mm_cpus_allowed) and is only num_possible_cpus()
bits wide, so clearing bit 31 is a deterministic OOB bit-clear at a
fixed offset of 2^31 / 8 == 256 MiB past the bitmap base. The address is
not attacker-influenced (fixed sentinel -> fixed offset) and the op only
clears a single bit; what sits 256 MiB further along the direct map is
whatever kernel object happens to live there, so this corrupts one bit of
unpredictable kernel memory -- it is not an arbitrary-address or
arbitrary-value write.
It triggers only in per-CPU CID mode, when a CPU is running an active
task of the target mm whose cid is still MM_CID_UNSET -- the
fork()/execve() window before that task's next schedule-in assigns it a
real CID -- and a per-CPU -> per-task fixup walks over it (the mode
fallback driven by a thread exit, sched_mm_cid_exit(), or by the deferred
max_cids recompute in mm_cid_work_fn()).
In practice syzkaller surfaced it as a KASAN use-after-free reported in
__schedule -> mm_cid_switch_to, where the offending clear_bit() is inlined
via mm_cid_schedout() -> mm_drop_cid().
Guard the transition-bit assignment against MM_CID_UNSET, in addition to
the existing cid_in_transit() check, so the bit is only set on a genuine
task-owned CID. A CPU-owned (MM_CID_ONCPU) CID of a running active task
is handled by the cid_on_cpu(pcp->cid) branch above and never reaches
this path, so excluding MM_CID_UNSET (and the already-transitioning case)
is sufficient.Linux Linux Kernel High CVSS 7.8 CVE-2026-63800In the Linux kernel, the following vulnerability has been resolved:
pNFS: Fix use-after-free in pnfs_update_layout()
When hitting the NFS_LAYOUT_RETURN branch in pnfs_update_layout(),
the code calls pnfs_prepare_to_retry_layoutget(lo). If it succeeds,
pnfs_put_layout_hdr(lo) is called before trace_pnfs_update_layout(),
which still references 'lo'. This results in a use-after-free when the
tracepoint accesses lo's fields.
Fix this by moving the tracepoint call before pnfs_put_layout_hdr(lo).Linux Linux Kernel Critical CVSS 9.8 CVE-2026-63801In the Linux kernel, the following vulnerability has been resolved:
tipc: fix slab-use-after-free Read in tipc_aead_decrypt_done
tipc_aead_decrypt() goes straight from tipc_bearer_hold(b) to
crypto_aead_decrypt(req) without taking a reference on the netns, unlike
the encrypt path. When crypto_aead_decrypt() is offloaded asynchronously
(e.g. the SIMD aead wrapper queuing to cryptd), the cryptd worker runs
tipc_aead_decrypt_done() later. If the bearer's netns is torn down in the
meantime, cleanup_net() -> tipc_exit_net() -> tipc_crypto_stop() frees the
per-netns tipc_crypto, and the completion then reads it:
tipc_aead_decrypt_done() dereferences aead->crypto->stats and
aead->crypto->net, and tipc_crypto_rcv_complete() dereferences
aead->crypto->aead[] and the node table -- reading freed memory.
Decoded KASAN splat (v7.1-rc7, CONFIG_KASAN_INLINE + TIPC + TIPC_CRYPTO):
BUG: KASAN: slab-use-after-free in tipc_aead_decrypt_done (net/tipc/crypto.c:999)
Read of size 8 at addr ffff8881056258a8 by task kworker/u16:2/51
Workqueue: events_unbound
Call Trace:
tipc_aead_decrypt_done (net/tipc/crypto.c:999)
process_one_work (kernel/workqueue.c:3314)
worker_thread (kernel/workqueue.c:3397 kernel/workqueue.c:3478)
kthread (kernel/kthread.c:436)
ret_from_fork (arch/x86/kernel/process.c:158)
ret_from_fork_asm (arch/x86/entry/entry_64.S:245)
Allocated by task 169:
__kasan_kmalloc (mm/kasan/common.c:398 mm/kasan/common.c:415)
tipc_crypto_start (net/tipc/crypto.c:1502)
tipc_init_net (net/tipc/core.c:72)
ops_init (net/core/net_namespace.c:137)
setup_net (net/core/net_namespace.c:446)
copy_net_ns (net/core/net_namespace.c:579)
create_new_namespaces (kernel/nsproxy.c:132)
__x64_sys_unshare (kernel/fork.c:3316)
do_syscall_64 (arch/x86/entry/syscall_64.c:63)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121)
Freed by task 8:
kfree (mm/slub.c:6566)
tipc_exit_net (net/tipc/core.c:119)
cleanup_net (net/core/net_namespace.c:704)
process_one_work (kernel/workqueue.c:3314)
kthread (kernel/kthread.c:436)
This is the same class of bug that commit e279024617134 ("net/tipc: fix
slab-use-after-free Read in tipc_aead_encrypt_done") fixed for the encrypt
side. The encrypt path takes maybe_get_net(aead->crypto->net) before
crypto_aead_encrypt() and drops it with put_net() on the synchronous
return paths and in tipc_aead_encrypt_done(); the -EINPROGRESS/-EBUSY
return keeps the reference for the async callback to release. The decrypt
path was left without the equivalent guard.
Mirror the encrypt-side fix on the decrypt path: take a net reference
before crypto_aead_decrypt() (failing with -ENODEV and the matching
bearer put if it cannot be acquired), keep it across the
-EINPROGRESS/-EBUSY async return, and drop it with put_net() on the
synchronous success/error return and at the end of
tipc_aead_decrypt_done().
Reproduced under KASAN on v7.1-rc7: a UDP bearer with a cluster key is
flooded with crafted encrypted frames from an unknown peer (driving the
cluster-key decrypt path) while the bearer's netns is repeatedly torn
down. The completion must run asynchronously to outlive
tipc_crypto_stop(); on x86 the stock aesni gcm(aes) now decrypts
synchronously, so the async path was exercised via cryptd offload. The
unguarded aead->crypto dereference in tipc_aead_decrypt_done() is the
unpatched upstream path; tipc_aead_decrypt() still lacks
maybe_get_net(aead->crypto->net), so the completion can outlive the free
on any config where crypto_aead_decrypt() goes async.
Found by 0sec automated security-research tooling (https://0sec.ai).Linux Linux Kernel High CVSS 8.8 CVE-2026-63802In the Linux kernel, the following vulnerability has been resolved:
blk-cgroup: fix UAF in __blkcg_rstat_flush()
When multiple blkgs in the same blkcg are released concurrently,
a use-after-free can occur. The race happens when one blkg's
__blkcg_rstat_flush() removes another blkg's iostat entries via
llist_del_all(). The second blkg sees an empty list and proceeds
to free itself while the first is still iterating over its entries.
Move the flush from __blkg_release() (RCU callback) to blkg_release()
(before call_rcu). This ensures the RCU grace period waits for any
concurrent flush's rcu_read_lock() section to complete before freeing.Linux Linux Kernel High CVSS 7.8 CVE-2026-63803In the Linux kernel, the following vulnerability has been resolved:
hdlc_ppp: sync per-proto timers before freeing hdlc state
Each PPP control protocol (LCP/IPCP/IPV6CP) embedded in struct ppp
registers a timer via timer_setup(). That struct ppp is the
hdlc->state allocation, which detach_hdlc_protocol() frees with kfree()
in both teardown paths: unregister_hdlc_device() and the re-attach inside
attach_hdlc_protocol().
The ppp proto never registered a .detach callback, so
detach_hdlc_protocol() performs no timer synchronization before the
kfree(). The only cancel, timer_delete(&proto->timer) in ppp_cp_event(),
is partial (it does not wait for a running callback) and only runs on the
->CLOSED transition; ppp_stop()/ppp_close() do not sync either. A
ppp_timer callback already executing (blocked on ppp->lock) survives the
kfree and then dereferences proto->state / ppp->lock in freed memory,
leading to a use-after-free.
Fix this by adding a .detach helper that calls timer_shutdown_sync() on
every per-proto timer. detach_hdlc_protocol() invokes proto->detach(dev)
before kfree(hdlc->state), so timer_shutdown_sync()
now runs on both free paths.
timer_shutdown_sync() is used instead of timer_delete_sync() because the
keepalive path re-arms the timer through add_timer()/mod_timer() and
shutdown blocks any re-activation during teardown.
Initialize the per-protocol timers in ppp_ioctl() when the protocol is
attached, and remove the now-redundant timer_setup() from ppp_start(), so
that the timers are initialized exactly once at attach time and
ppp_timer_release() never operates on uninitialized timer_list
structures. attach_hdlc_protocol() uses kmalloc() (not kzalloc), so
struct ppp's protos[i].timer is uninitialized garbage until the first
timer_setup(); without this init-at-attach, attaching the PPP protocol
without ever bringing the device up would leave timer_shutdown_sync()
operating on uninitialized memory in .detach. Moving the init out of
ppp_start() (which only runs on NETDEV_UP) into the attach path makes the
initialization unconditional and avoids initializing the same timer_list
twice.
This bug was found by static analysis.Linux Linux Kernel High CVSS 7.8 CVE-2026-63804In the Linux kernel, the following vulnerability has been resolved:
gfs2: fix use-after-free in gfs2_qd_dealloc
gfs2_qd_dealloc(), called as an RCU callback from gfs2_qd_dispose(),
accesses the superblock object sdp through qd->qd_sbd after freeing qd.
It does so to decrement sd_quota_count and wake up sd_kill_wait.
However, by the time the RCU callback runs, gfs2_put_super() may have
already freed sdp via free_sbd(). This can happen when
gfs2_quota_cleanup() is called during unmount: it disposes of quota
objects via call_rcu() and then waits on sd_kill_wait with a 60-second
timeout. If the timeout expires, or if gfs2_gl_hash_clear() triggers
additional qd_put() calls that schedule more RCU callbacks after the
wait completes, gfs2_put_super() will proceed to free the superblock
while RCU callbacks referencing it are still pending.
Add an rcu_barrier() before free_sbd() in gfs2_put_super() to ensure
all pending RCU callbacks (including gfs2_qd_dealloc) have completed
before the superblock is freed.Linux Linux Kernel High CVSS 7.8 CVE-2026-63805In the Linux kernel, the following vulnerability has been resolved:
crypto: nx - fix nx_crypto_ctx_exit argument
nx_crypto_ctx_shash_exit calls nx_crypto_ctx_exit with crypto_shash_ctx(...)
but crypto_shash_ctx gives a nx_crypto_ctx *, not a crypto_tfm *.
Fix the type in nx_crypto_ctx_exit and drop the bogus crypto_tfm_ctx
call.
This fixes the following oops:
BUG: Unable to handle kernel data access at 0xc0403effffffffc8
Faulting instruction address: 0xc000000000396cb4
Oops: Kernel access of bad area, sig: 11 [#15]
Call Trace:
nx_crypto_ctx_shash_exit+0x24/0x60
crypto_shash_exit_tfm+0x28/0x40
crypto_destroy_tfm+0x98/0x140
crypto_exit_ahash_using_shash+0x20/0x40
crypto_destroy_tfm+0x98/0x140
hash_release+0x1c/0x30
alg_sock_destruct+0x38/0x60
__sk_destruct+0x48/0x2b0
af_alg_release+0x58/0xb0
__sock_release+0x68/0x150
sock_close+0x20/0x40
__fput+0x110/0x3a0
sys_close+0x48/0xa0
system_call_exception+0x140/0x2d0
system_call_common+0xf4/0x258
.. which came from hardlink(1) opportunistically using AF_ALG.
The same problem exists with nx_crypto_ctx_skcipher_exit getting a context
it wasn't expecting, but apparently nobody hit that for years.Linux Linux Kernel High CVSS 7.8 CVE-2026-63806In the Linux kernel, the following vulnerability has been resolved:
KVM: Replace guest-triggerable BUG_ON() in ioeventfd datamatch with get_unaligned()
Drop a BUG_ON() that has been reachable since it was first added, way back
in 2009, and instead use get_unaligned() to perform potentially-unaligned
accesses.
For a given store, KVM x86's emulator tracks the entire value in the
destination operand, x86_emulate_ctxt.dst. If the destination is memory,
and the target splits multiple pages and/or is emulated MMIO, then KVM
handles each fragment independently. E.g. on a page split starting at page
offset 0xffc, KVM writes 4 bytes to the first page, then the remaining
bytes to the second page, using ctxt->dst as the source for both (with
appropriate offsets).
If the destination splits a page *and* hits emulated MMIO on the second
page, then KVM will complete the write to the first page, then emulate the
MMIO access to the second page. If there is a datamatch-enabled ioeventfd
at offset 0 of the second page, then KVM will process the remainder of the
store as a potential ioeventfd signal.
Putting it all together, if the guest emits a store that splits a page
starting at page offset N, and the second page has a datamatch-enabled
ioeventfd at offset 0, then KVM will check for datamatch using
&dst.valptr[N] as the source. Due to dst (and thus dst.valptr) being
32-byte aligned, if N is not aligned to @len, the BUG_ON() fires.
E.g. with a 16-byte store at page offset 0xffc, to an ioeventfd of len 8,
all initial checks in ioeventfd_in_range() will succeed, and the BUG_ON()
fires due to @val being 4-byte aligned, but not 8-byte aligned.
------------[ cut here ]------------
kernel BUG at arch/x86/kvm/../../../virt/kvm/eventfd.c:783!
Oops: invalid opcode: 0000 [#1] SMP
CPU: 0 UID: 1000 PID: 615 Comm: repro Not tainted 7.1.0-rc2-ff238429d1ea #365 PREEMPT
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:ioeventfd_write+0x6c/0x70 [kvm]
Call Trace:
<TASK>
__kvm_io_bus_write+0x85/0xb0 [kvm]
kvm_io_bus_write+0x53/0x80 [kvm]
vcpu_mmio_write+0x66/0xf0 [kvm]
emulator_read_write_onepage+0x12a/0x540 [kvm]
emulator_read_write+0x109/0x2b0 [kvm]
x86_emulate_insn+0x4f8/0xfb0 [kvm]
x86_emulate_instruction+0x181/0x790 [kvm]
kvm_mmu_page_fault+0x313/0x630 [kvm]
vmx_handle_exit+0x18a/0x590 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0xc81/0x1c90 [kvm]
kvm_vcpu_ioctl+0x2d5/0x970 [kvm]
__x64_sys_ioctl+0x8a/0xd0
do_syscall_64+0xb7/0x890
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f19c931a9bf
</TASK>
Modules linked in: kvm_intel kvm irqbypass
---[ end trace 0000000000000000 ]---
In a perfect world, the fix would be to simply delete the BUG_ON(), as KVM
x86 doesn't perform alignment checks on "normal" memory accesses at CPL0.
Sadly, C99 ruins all the fun; while the x86 architecture plays nice,
dereferencing an unaligned pointer directly is undefined behavior in C,
e.g. triggers splats when running with CONFIG_UBSAN_ALIGNMENT=y.Linux Linux Kernel High CVSS 7.1 CVE-2026-63807In the Linux kernel, the following vulnerability has been resolved:
KVM: x86/mmu: Ensure hugepage is in by slot before checking max mapping level
When recovering hugepages in the shadow MMU, verify that the base gfn of
the shadow page is actually contained within the target memslot, *before*
querying the max mapping level given the shadow page's gfn. Failure to
pre-check the validity of the gfn can lead to an out-of-bounds access to
the slot's lpage_info (which typically manifests as a host #PF because the
lpage_info is vmalloc'd) if the guest creates a hugepage mapping (in its
PTEs) that extends "below" the bounds of a memslot.
When faulting in memory for a guest, and the size of the guest mapping is
greater than KVM's (current) max mapping, then KVM will create a "direct"
shadow page (direct in that there are no gPTEs to shadow, and so the target
gfn is a direct calculation given the base gfn of the shadow page). The
hugepage recovery flow looks for such direct shadow pages, as forcing 4KiB
mappings when dirty logging generates the guest > host mapping size case.
When the 4KiB restriction is lifted, then KVM can replace the shadow page
with a hugepage.
But if KVM originally used a smaller mapping than the guest because the
range of memory covered by the guest hugepage exceeds the bounds of a
memslot, then KVM will link a direct shadow page with a gfn that is outside
the bounds of the memslot being used to fault in memory. The rmap entry
added for the leaf mapping is correct and within bounds, but the gfn of the
leaf SPTE's parent shadow page will be out of bounds.
BUG: unable to handle page fault for address: ffffc90000806ffc
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 100000067 P4D 100000067 PUD 1002a7067 PMD 10612f067 PTE 0
Oops: Oops: 0000 [#1] SMP
CPU: 13 UID: 1000 PID: 757 Comm: mmu_stress_test Not tainted 7.1.0-rc1-48ce1e26eace-x86_pir_to_irr_comments-vm #341 PREEMPT
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:kvm_mmu_max_mapping_level+0x79/0x2b0 [kvm]
Call Trace:
<TASK>
kvm_mmu_recover_huge_pages+0x21b/0x320 [kvm]
kvm_set_memslot+0x1ee/0x590 [kvm]
kvm_set_memory_region.part.0+0x3a1/0x4d0 [kvm]
kvm_vm_ioctl+0x9bf/0x15d0 [kvm]
__x64_sys_ioctl+0x8a/0xd0
do_syscall_64+0xb7/0xbb0
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f21c0f1a9bf
</TASK>
Don't bother pre-checking the bounds of the potential hugepage, i.e. don't
check that e.g. sp->gfn + KVM_PAGES_PER_HPAGE(sp->role.level + 1) is also
within the memslot, as the checks performed by kvm_mmu_max_mapping_level()
are a superset of the basic bounds checks. I.e. pre-checking the full
range would be a dubious micro-optimization.Linux Linux Kernel High CVSS 8.8 CVE-2026-64088In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: fix negative tt_buff_len
batadv_orig_node::tt_buff_len was declared as s16, but the field is never
intended to hold a negative value. When a value greater than 32767 is
assigned, it wraps to a negative signed integer.
In batadv_send_other_tt_response(), tt_buff_len is temporarily widened to
s32. The incorrectly negative s16 value propagates into the s32, causing
batadv_tt_prepare_tvlv_global_data() to allocate a full sized buffer but
populates only a small portion of it with the collected changeset. All
remaining bits are kept uninitialized.
Using an u16 avoids this type confusion and ensures that no (negative) sign
extension is performed in batadv_send_other_tt_response().Linux Linux Kernel High CVSS 8.8 CVE-2026-64089In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: fix negative last_changeset_len
batadv_piv_tt::last_changeset_len len was declared as s16, but the field is
never intended to hold a negative value. When a value greater than 32767 is
assigned, it wraps to a negative signed integer.
In batadv_send_my_tt_response(), last_changeset_len is temporarily widened
to s32. The incorrectly negative s16 value propagates into the s32, causing
batadv_tt_prepare_tvlv_local_data() to allocate a full sized buffer but
populates only a small portion of it with the collected changeset. All
remaining bits are kept uninitialized.
Using an u16 avoids this type confusion and ensures that no (negative) sign
extension is performed in batadv_send_my_tt_response().Linux Linux Kernel Critical CVSS 9.8 CVE-2026-64091In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: fix TOCTOU race for reported vlans
The local TT based TVLV is generated by first checking the number of VLANs
which have at least one TT entry. A new buffer with the correct size for
the VLANs is then allocated. Only then, the list of VLANs s used to fill
the VLAN entries in the buffer. During this time, the meshif_vlan_list_lock
is held. But the actual number of TT entries of each VLAN can still
increase during this time - just not the number of VLANs in the list.
But the prefilter used in the buffer size calculation might still cause an
increase of the number of VLANs which need to be stored. Simply because a
VLAN might now suddenly have at least one entry when it had none in the
pre-alloc check - and then needs to occupy space which was not allocated.
It is better to overestimate the buffer size at the beginning and then fill
the buffer only with the VLANs which are not empty.Linux Linux Kernel Critical CVSS 9.8 CVE-2026-64093In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tp_meter: directly shut down timer on cleanup
batadv_tp_sender_cleanup() was calling timer_delete_sync() followed by
timer_delete() to guard against the timer handler re-arming itself between
the two calls. This double-deletion hack relied on the sending status being
set to 0 to suppress re-arming.
Replace both calls with a single timer_shutdown_sync(). This function both
waits for any running timer callback to complete (like timer_delete_sync())
and permanently disarms the timer so it cannot be re-armed afterwards,
making re-arming prevention unconditional and self-documenting.
The re-arming property is also required because otherwise:
1. context 0 (batadv_tp_recv_ack()) checks in
batadv_tp_reset_sender_timer() if sending is still 1 -> it is
2. context 1 changes in batadv_tp_sender_shutdown() sending to 0 and in
this process forces the kthread to stop timer in
batadv_tp_sender_cleanup()
3. context 0 continues in batadv_tp_reset_sender_timer() and rearms the
timer -> but the reference for it is already goneLinux Linux Kernel High CVSS 8.8 The 100 most recent.